Bedienungsanleitung Karcher SP 6 Flat Inox (Seite 11 von 168) (Alle Sprachen)

657266

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

– 2

NOTICE

The shorter the hose length and the larger the hose di-

ameter, the higher the pump capacity.

In order to prevent the pump from clogging, use the en-

closed pre-filter (SP 6 Flat Inox) or slide down the inte-

grated pre-filter (SP 7 Dirt Inox) with hose diameters of

less than 1¼ “.

The pump connection is equipped with a plug system

(Quick-Connect).

The unmounted connection nozzle with pump connect-

ing piece is enclosed in the device.

Illustration

 To remove the connection nozzle, press the Quick-

Connect (grey button).

Illustration

 Screw the pump connecting piece onto the connec-

tion nozzle.

 Slide the hose clamp onto the hose.

 Slide the hose onto the pump connecting piece and

secure it by means of a hose clamp.

 Slide the connection nozzle into the Quick-Con-

nect.

NOTICE

Hoses with a diameter of 1“, 1¼“ and 1½“ can be con-

nected to the pump connecting piece.

A sufficiently large hose diameter must be selected and

the pump connecting piece must be shortened accord-

ing to the grooves so that the required particle size can

be used. A large hose diameter is also recommended

for smaller particle sizes to allow a high flow volume.

Illustration

 Slide the level sensor onto the rail from the top.

Illustration

 Fold out or fold in the support legs (SP 6 Flat Inox)

for the pump start.

NOTICE

It is not mandatory to fold out the support legs; a higher

pump capacity is achieved by folding out the support

legs.

Folding in the support legs enables the flat vacuuming

of the fluid up to a residual fluid height of up to 1 mm.

 Install or uninstall pre-filter (SP 6 Flat Inox).

 Slide down or up the pre-filter (SP 7 Dirt Inox).

NOTICE

It is not necessary to install the pre-filter, but a higher

pump capacity is reached by installing the pre-filter (on-

ly for SP 6 Flat Inox).

The feed fluids are pre-filtered by the pre-filter to protect

the pump from heavy contamination. Particles up to 5

mm can still be used in the filter.

Disassembly of the pre-filter allows for the flat vacuum-

ing of the fluid up to 1 mm residual fluid height (SP 6 Flat

Inox).

 Safely place the pump on a stable surface in the

feed fluid or immerse it using a rope tied to the car-

rying handle.

NOTICE

The suction area must not be blocked by soiling.

In case of muddy ground, place the pump on a brick or

the like.

Ensure that the pump is level.

Do not carry the pump on the cable or the hose.

몇 DANGER

Risk of mortal danger on account of electric shock!

Do not touch feed fluids, the rope attached to the carry-

ing handle as well as objects that are in contact with the

feed fluid (e.g. pipelines extending into the water, rail-

ings, etc.).

Illustration

NOTICE

In order for the pump to draw independently, the fluid

level must be at least 50 mm (SP 7 Dirt Inox) or 7 mm

(SP 6 Flat Inox).

The pump can pump up to a residual fluid height of

35 mm (SP 7 Dirt Inox) or 1 mm (SP 6 Flat Inox).

Illustration

With a low fluid level, possibly drawn air or air that is

present in the pump escapes via the automatic venting

device. In addition, fluid may leak at this spot.

If the pump has suction problems with a low fluid level,

unplug and plug in the mains plug repeatedly in order to

support the suction process.

Illustration

NOTICE

In the automatic mode, the level sensor automatically

controls the pumping operations.

As soon as the level sensor has contact with the rising

feed fluid the pump switches on.

The pump switches off as soon as the level sensor loses

contact with the falling feed fluid and an after-running

time of 15 s has passed.

Switching on:

Minimum fluid level required to enable the pump to suc-

tion independently (=minimum switch-on point):

SP 6 Flat Inox: 7 mm (57 mm when using the pre-filter)

SP 7 Dirt Inox: 50 mm

Highest adjustable switching height of the level

sensor:

SP 6 Flat Inox: 190 mm without pre-filter (240 mm when

using the pre-filter)

SP 7 Dirt Inox: 237 mm

Minimum residual fluid height/max. Extraction

depth:

The pump can pump out up to a residual liquid height of

SP 6 Flat Inox: 1 mm (without pre-filter, with folded

base)

SP 7 Dirt Inox: 35 mm

NOTICE

It is recommended to use the pre-filter.

NOTICE

Ensure that the pump is level.

Otherwise it can happen that the level sensor does not

lose the fluid contact and the pump runs dry.

 Push the level sensor to the desired switch-on

height (contact with feed fluid).

Start up Operation

General

Automatic venting device

Automatic operation

11EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher SP 6 Flat Inox Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info