Bedienungsanleitung Karcher SP 9.000 Flat (Seite 10 von 148) (Alle Sprachen)

803797

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

10 English

7Pump connecting piece G 1 ½ (1″, 1 ¼″ and 1 ½″

hose connection and G 1 ½ - thread)

8 Pipe union (G 1 ½ - thread)

9 Float switch

10 Quick-Connect

11 Automatic venting device

12 Feet (SP 9.000 Flat)

*Not included in the scope of delivery.

Initial startup

DANGER

Risk of electric shock and risk of injury!

The device contains electrical and mechanical compo-

nents.

Always disconnect the device from the power supply

before assembling, disassembling or cleaning.

Note

The shorter the hose length and larger the hose diame-

ter, the higher the pump capacity.

To avoid clogging the pump, use a pre-filter for hose di-

ameters smaller than 1 ¼″.

The pump connection is equipped with a plug-in system

(Quick-Connect).

The pipe union with pump connecting piece G 1 ½ and

the G 1 threaded connection are supplied unassembled

with the device.

Note

Hoses with a diameter of 1″, 1 ¼″ and 1 ½″ can be con-

nected to the pump connecting piece G 1 ½.

A sufficiently large hose diameter must be selected and

the pump connecting piece G 1 ½ must be shortened

according to the grooves so that the required particle

size can be used. A large hose diameter is also recom-

mended for smaller particle sizes to allow a high flow

volume.

Connect hose to pump if using a 1″, 1 ¼″ or 1 ½″

hose:

1 Screw the pump connecting piece G 1 ½ onto the

pipe union.

Illustration B

2 Push the hose clamp onto the hose.

3 Push the hose onto the pump connecting piece G 1

½ and fasten it with a hose clamp.

4 Push the pipe union into the Quick-Connect.

Illustration C

Connect hose to pump if using a ¾″ or 1″ hose:

1 Screw the G1 threaded connection onto the pipe un-

ion.

Illustration B

2 Fit the special accessory pump connecting piece G

1 (6.997-359.0 pump connecting piece G 1 (33.3

mm) incl. check valve - not included in the scope of

delivery) onto the G 1 threaded connection:

a Place the check valve on the G 1 threaded con-

nection so that the lettering ‘UP’ is legible.

b Screw the pump connecting piece G 1 onto the G

1 threaded connection.

3 Push the hose clamp onto the hose.

4 Push the hose onto the pump connecting piece G 1

and fasten it with a hose clamp.

5 Push the pipe union into the Quick-Connect.

Illustration C

Setting up / immersing the pump:

1 Fold out or in the feet (SP 9.000 Flat).

Illustration D

2 Place the pump securely on solid ground in the feed

fluid or immerse it by means of a rope attached to

the carrying handle.

Note

The suction area must not be blocked by contamination.

If the ground is muddy, place the pump on a brick or

something similar. Make sure that the pump is horizon-

tal. Do not carry the pump using the cable or hose.

Operation

DANGER

Danger of death from electric shock.

Danger of death from electric shock if live parts are

touched.

During operation, do not touch the rope attached to the

carrying handle or any objects that are in contact with

the pumped liquid (e.g. pipelines protruding into the

pumped liquid, railings) and do not reach into the

pumped liquid.

Automatic venting device

1. If the fluid level is low, any sucked-in air, or air pres-

ent in the pump, may escape via the automatic vent-

ing device. Fluid can also leak along with air.

If the pump has problems with suction when the fluid

level is low, unplug and plug in the mains plug re-

peatedly to assist the suction process.

Illustration E

Automatic mode

1. If necessary, fold out the feet, see chapter Initial

startup (SP 9.000 Flat).

Note

Folding out the feet is not absolutely necessary, but it

does increase the pump capacity.

2. Plug the mains plug into a mains socket.

Note

In automatic mode, the float switch controls the pump-

ing process automatically.

The pump switches on as soon as the float switch has

reached the switch-on height caused by the rising fluid

level.

The pump switches off as soon as the float switch has

reached the switch-off height caused by the sinking fluid

level.

The float switch must be able to move freely.

Illustration F

* The switching heights vary depending on the posi-

tion of the float switch.

Manual operation

Note

In manual operation, the pump stays switched on con-

tinuously. For the pump to suction itself in manual

mode, the fluid level must be at least 60 mm (SP 9.500

Dirt and SP 11.000 Dirt) or 7 mm (SP 9.000 Flat).

Min / Max SP 9.000

Flat

SP 9.500

Dirt

SP 11.000

Dirt

Switch-on

height cm*

36 / 44 43 / 50 43 / 50

Switch-off

height cm*

15 / 24 18 / 30 18 / 30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher SP 9.000 Flat Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info