Bedienungsanleitung Karcher VC 4 Cordless Premium myHome (Seite 14 von 160) (Alle Sprachen)

803792

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

14 English

1. Switch off the device.

2. Manually cleaning the air inlet filter.

a Pull the soiled air inlet filter down at the filter stick,

carefully beat it and clean it with a damp cloth or

running water.

Illustration K

b Reinsert the fully dried air inlet filter.

c Check for correct seating.

3. Cleaning the air inlet filter with a filter cleaning

device.

Note

A new air inlet filter must be installed in the dust contain-

er during filter cleaning.

a Push the filter cleaning device on to the suction

pipe branch and pull the air inlet filter out of the

device using the filter stick.

b Push the soiled air inlet filter into the filter clean-

ing device.

c Insert a new air inlet filter into the dust container.

Illustration L

d Switch on the device and let it run in boost mode

while turning the side cover.

Illustration M

e Remove the cleaned air inlet filter from the filter

cleaning tool and reinsert it in the dust container

after removing the new air inlet filter.

f Check that the air inlet filter is correctly seated.

Cleaning the dust container and cyclone filter

Note

The dust container and cyclone filter can be cleaned

with or without removing the dust container.

We recommend removing the dust container from the

device for easy cleaning.

Note

Before cleaning the dust container and cyclone filter,

empty the dust container, see chapter Ending operation

1. Switch off the device.

2. Press the unlocking button for the dust container and re-

move the dust container from the hand-held device.

Illustration N

a Remove the cyclone filter from the dust container

by turning it anticlockwise.

b Remove the cyclone filter from the dust container

and take the air inlet filter out of the cyclone filter.

Illustration O

ATTENTION

Short circuit hazard

There are cables or contacts in the dust container and

cyclone filter for the power supply.

Make sure that the cables or contacts do not get wet

when cleaning.

3. Clean the dust container and cyclone filter with a

soft brush or a slightly damp cloth.

Illustration P

4. Clean the air inlet filter, see chapter Cleaning the air

inlet filter

5. Re-insert the dry dust container and cyclone filter

with air inlet filter into the device and close the flap.

6. Attach the dust container to the handheld device.

a Hold the dust container at an angle against the

handheld device while holding the top on the

hook of the handheld device.

b Push the dust container upwards until the hook

on the handheld device engages in the slot in the

dust container.

c The dust container must audibly click into place.

Illustration Q

Clean the exhaust air foam filter/replace the

exhaust air foam filter

Note

The exhaust air foam filter ensures pure exhaust air.

●Clean the exhaust air foam filter if it is visibly dirty.

●Replace the exhaust air foam filter if damage is visible.

1. Switch off the device.

2. Clean the exhaust air foam filter.

a Press both side unlocking buttons at the same

time and remove the cover with the exhaust air

foam filter.

Illustration R

ATTENTION

Short circuit hazard

Power supply cables or contacts are located in the cov-

er of the exhaust air foam filter.

Before cleaning with water, remove the cover from the

exhaust air foam filter so that the cables or contacts do

not get wet.

3. Carefully tap off the exhaust air foam filter or if it is

heavily soiled:

a Pull off the cover of the exhaust air foam filter.

b Clean the exhaust air foam filter under running

water. Do not rub or brush off.

ATTENTION

Health risk

Exhaust air foam filters that are not completely dry when

installed in the device can be a breeding ground for

spores and mould.

Make sure that the exhaust air foam filter is completely

dry on installation.

c Then allow the exhaust air foam filter to dry com-

pletely.

d Fasten the cover to the exhaust air foam filter.

Illustration S

e Insert the exhaust air foam filter into the device

until it latches into place.

f Press the cover down in the middle to ensure that

the cover sits correctly on the device.

Illustration U

4. Replace the exhaust air foam filter.

a Press both side unlocking buttons at the same

time and remove the exhaust air foam filter.

Illustration R

b Remove the cover of the exhaust air foam filter

and dispose of the used filter.

c Fasten the new exhaust air foam filter to the cover.

Illustration T

d Insert the exhaust air foam filter into the device

until it latches into place.

e Press the cover down in the middle to ensure that

the cover sits correctly on the device.

Illustration U

Cleaning the multi-function nozzle

1. Switch off the device.

2. Remove accessories.

ATTENTION

Short circuit hazard

The multi-function brush contains electrical compo-

nents.

You must not immerse the multi-function brush in water

or clean it with a damp cloth.

3. Clean the multi-function brush.

a Unlock the brush roll cover / support with a coin

or other object and remove it.

Illustration V

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher VC 4 Cordless Premium myHome Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info