Bedienungsanleitung Karcher VC 6 Cordless ourFamily (Seite 15 von 164) (Alle Sprachen)

803789

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

English 15

d Remove the cleaned air inlet filter from the filter

cleaning tool and reinsert it in the dust container

after removing the new air inlet filter.

e Check that the air inlet filter is correctly seated.

Cleaning the dust container and cyclone filter

Note

Before cleaning the dust container and cyclone filter,

empty the dust container, see chapter Ending operation

1 Switch off the device.

2 Remove the cyclone filter and air inlet filter.

a Remove the cyclone filter from the dust container

by turning it anticlockwise.

b Remove the cyclone filter from the dust container

and take the air inlet filter out of the cyclone filter.

Illustration P

ATTENTION

Short circuit hazard

There are cables or contacts in the dust container and

cyclone filter for the power supply.

Make sure that the cables or contacts do not get wet

when cleaning.

3 Clean the dust container and cyclone filter with a

soft brush or a slightly damp cloth

Illustration Q

4 Clean the air inlet filter, see chapter Cleaning the air

inlet filter

5 Re-insert the dry dust container and cyclone filter

with air inlet filter into the device and close the flap.

Cleaning the HEPA filter/replacing the HEPA

filter

Note

The HEPA filter ensures clean exhaust air.

●Clean the HEPA filter if it is visibly dirty.

●Replace the HEPA filter if there is visible damage.

1. Switch off the device.

2. Cleaning the HEPA filter.

a Pull the HEPA filter cover with the HEPA filter out

of the device.

Illustration R

ATTENTION

Short circuit hazard

Power supply cables or contacts are located in the cov-

er of the HEPA filter.

Before cleaning with water, remove the cover of the

HEPA filter so that the cables or contacts do not get wet.

3. Carefully knock off the HEPA filter or if it is very dirty:

a Unscrew/remove the cover of the HEPA filter.

b Clean the HEPA filter under running water. Do not

rub or brush off.

c Then let the HEPA filter dry completely.

Illustration S

d Fasten/screw on the HEPA filter cover.

ATTENTION

Health risk

HEPA filters that are not completely dry when installed

in the device can be a breeding ground for spores and

mould.

Make sure that the HEPA filter is completely dry on in-

stallation.

4. Insert the dry HEPA filter into the device.

Illustration U

Note

The HEPA filter only needs to be inserted into the de-

vice, a magnet allows the HEPA filter to snap into place

automatically.

5. Replacing the HEPA filter

a Pull the HEPA filter cover with the HEPA filter out

of the device.

Illustration R

b Unscrew/pull off the cover of the HEPA filter and

dispose of the used filter.

c Attach/screw on the new HEPA filter cover.

Illustration T

6. Insert the HEPA filter into the device.

Illustration U

Cleaning the multi-function nozzle

1. Switch off the device.

2. Remove accessories.

ATTENTION

Short circuit hazard

The multi-function brush contains electrical compo-

nents.

You must not immerse the multi-function brush in water

or clean it with a damp cloth.

3. Clean the multi-function brush.

a Unlock the brush roll cover / support with a coin

or other object and remove it.

Illustration V

b Remove the brush roll from the brush opening in

the direction of the arrow.

Illustration W

c Remove the dirt e.g. with a brush. If necessary,

the brush roll can be cleaned under running wa-

ter.

The brush roll must be completely dry before re-

installation.

d Carefully clean the brush opening with a cloth or

soft brush.

Illustration X

e Insert the brush roll into the brush opening.

f Lock the brush roll with a coin or other object.

Illustration Y

Troubleshooting guide

Malfunctions often have simple causes that you can

remedy yourself using the following overview. When in

doubt, or in the case of malfunctions not mentioned

here, please contact your authorised Customer Service.

The device does not start up

Battery is empty.

Charge the rechargeable battery.

Battery is not inserted correctly.

Push the battery into the mount until it locks into

place.

Battery is defective.

Replace the battery.

The battery is not charging

The charging plug/mains plug is not connected correct-

ly.

Connect the charging plug/mains plug correctly.

The socket is defective.

Check that the socket is working.

The wrong charger is being used

Check that the correct charger is being used.

The device stops during operation or the suction

performance is poor

The battery has overheated.

Stop work and wait until the battery temperature is

back in the normal range.

The accessories, the suction opening on the dust con-

tainer or the suction pipes are clogged.

Remove the clog with a suitable aid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher VC 6 Cordless ourFamily Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info