Bedienungsanleitung Karcher VC 7 Cordless yourMax (Seite 16 von 184) (Alle Sprachen)

803788

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

16 English

Cleaning the air inlet filter with a filter cleaning de-

vice

Note

A new air inlet filter must be installed in the dust contain-

er during filter cleaning.

1 Switch off the device.

2 Push the filter cleaning device on to the suction pipe

branch and pull the air inlet filter out of the device us-

ing the filter stick.

Illustration P

a Push the soiled air inlet filter into the filter clean-

ing device.

b Insert a new air inlet filter into the dust container.

c Switch on the device and let it run in boost mode

while turning the side cover.

Illustration Q

d Remove the cleaned air inlet filter from the filter

cleaning tool and reinsert it in the dust container

after removing the new air inlet filter.

e Check that the air inlet filter is correctly seated.

Cleaning the dust container and cyclone filter

Note

Before cleaning the dust container and cyclone filter,

empty the dust container, see chapter Ending operation

1 Switch off the device.

2 Remove the cyclone filter and air inlet filter.

a Remove the cyclone filter from the dust container

by turning it anticlockwise.

b Remove the cyclone filter from the dust container

and take the air inlet filter out of the cyclone filter.

Illustration R

ATTENTION

Short circuit hazard

There are cables or contacts in the dust container and

cyclone filter for the power supply.

Make sure that the cables or contacts do not get wet

when cleaning.

3 Clean the dust container and cyclone filter with a

soft brush or a slightly damp cloth

Illustration S

4 Clean the air inlet filter, see chapter Cleaning the air

inlet filter

5 Re-insert the dry dust container and cyclone filter

with air inlet filter into the device and close the flap.

Cleaning the HEPA filter/replacing the HEPA

filter

Note

The HEPA filter ensures clean exhaust air.

●Clean the HEPA filter if it is visibly dirty.

●Replace the HEPA filter if there is visible damage.

1. Switch off the device.

2. Cleaning the HEPA filter.

a Pull the HEPA filter cover with the HEPA filter out

of the device.

Illustration T

ATTENTION

Short circuit hazard

Power supply cables or contacts are located in the cov-

er of the HEPA filter.

Before cleaning with water, remove the cover of the

HEPA filter so that the cables or contacts do not get wet.

3. Carefully knock off the HEPA filter or if it is very dirty:

a Unscrew/remove the cover of the HEPA filter.

b Clean the HEPA filter under running water. Do not

rub or brush off.

c Then let the HEPA filter dry completely.

Illustration U

d Fasten/screw on the HEPA filter cover.

ATTENTION

Health risk

HEPA filters that are not completely dry when installed in the

device can be a breeding ground for spores and mould.

Make sure that the HEPA filter is completely dry on in-

stallation.

4. Insert the dry HEPA filter into the device.

Illustration W

Note

The HEPA filter only needs to be inserted into the de-

vice, a magnet allows the HEPA filter to snap into place

automatically.

5. Replacing the HEPA filter

a Pull the HEPA filter cover with the HEPA filter out

of the device.

Illustration T

b Unscrew/pull off the cover of the HEPA filter and

dispose of the used filter.

c Attach/screw on the new HEPA filter cover.

Illustration V

6. Insert the HEPA filter into the device.

Illustration W

Cleaning the mini turbo nozzle

1. Switch off the device.

2. Remove accessories.

ATTENTION

Short circuit hazard

The mini turbo nozzle contains electrical components.

Do not immerse the mini turbo nozzle in water or clean

it with water.

3. Clean the mini turbo nozzle.

a Press down the brush roller cover and remove

the brush roller.

Illustration AB

b Remove residue, e.g. with a brush. Any tangled

threads or hairs can be carefully cut off with scissors.

c Carefully clean the brush opening with a cloth or

soft brush.

Illustration AC

d Diagonally insert the brush roller fully into the

brush opening, pressing upwards until the cover

has clicked into place.

Illustration AD

Cleaning the multi-function nozzle

1. Switch off the device.

2. Remove accessories.

ATTENTION

Short circuit hazard

The multi-function brush contains electrical compo-

nents.

You must not immerse the multi-function brush in water

or clean it with a damp cloth.

3. Clean the multi-function brush.

a Unlock the brush roll cover / support with a coin

or other object and remove it.

Illustration X

b Remove the brush roll from the brush opening in

the direction of the arrow.

Illustration Y

c Remove the dirt e.g. with a brush. Any tangled

threads or hairs can be carefully cut off with scis-

sors.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher VC 7 Cordless yourMax Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info