Bedienungsanleitung Karcher WD 2-18 Battery (Seite 11 von 124) (Alle Sprachen)

803414

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

English 11

Inserting the filter bag

1. Fully unfold the filter bag.

2. Attach the filter bag to the device connection and

press it on firmly.

Illustration D

3. Fit and lock the device head.

Illustration E

Note

We recommend using a filter bag to vacuum fine dust.

Installing the hose, pipes, floor nozzle

1. Connect the suction hose.

Illustration F

2. Connect the suction hose to the handle.

Illustration I

Note

For convenient vacuuming in confined spaces, the han-

dle can be removed, and the accessories plugged di-

rectly onto the suction hose.

To release the handle, the grey areas on both sides of

the handle must be pressed, and the handle pulled from

the hose.

3. Install the floor nozzle.

Install the insert in the floor nozzle.

Connect the floor nozzle to the suction pipes.

Illustration J

Fitting the battery pack

●Push the battery pack into the battery pack mount

from above until the battery pack latches into place.

ATTENTION

Only use battery packs from the KÄRCHER Battery

Power (+) platform with 18 V nominal voltage.

Illustration K

Starting up the device

Set the trigger into the desired position.

Illustration L

●Position "1 ON": The suction / blowing function is ac-

tivated.

●Position "0 OFF": The device is switched off.

Operation

Notes on operation

ATTENTION

Dirt/dust in the area of the battery holder

If dirt/dust accumulates in the area of the battery holder,

it may not be possible to properly insert or remove the

battery pack.

Keep the battery holder area clean.

ATTENTION

Static charge of the metal container

The metal container can become statically charged

when vacuuming large amounts of fine dust particles

and then discharge upon contact.

Note

Pay attention to the latest part numbers when purchas-

ing and installing filter bags and cartridge filters.

Information on accessories and spare parts can be

found at www.kaercher.com.

Dry vacuuming

ATTENTION

Vacuuming cold ashes

Device damage

Only vacuum cold ash with an ash pre-separator.

ATTENTION

Defective or wet foam filter / cartridge filter

Device damage

Before starting up, check the foam filter / cartridge filter

for damage, and replace it if necessary. Only vacuum

with a dry foam filter / cartridge filter.

Depending on the equipment variant, a foam filter or a

cartridge filter is included.

For devices with a foam filter: Always use the filter

bag in addition to the foam filter when dry vacuum-

ing.

For devices with a cartridge filter: Always use the fil-

ter bag in addition to the cartridge filter when vacu-

uming fine dust.

Note

Replace the filter bag in good time, as a filter bag that is

too full could be damaged. The fill degree of the filter

bag depends on the amount of dirt vacuumed. The filter

bag should be replaced more frequently when vacuum-

ing fine dust, sand, etc.

Wet vacuuming

ATTENTION

Wet vacuuming with a filter bag

Device damage

Do not use a filter bag when vacuuming wet.

ATTENTION

Operation with full container

When the container is full, a float switch closes the suc-

tion opening and the device runs at a higher speed.

Switch off the device immediately and empty the con-

tainer.

Note

If the device falls over, the float can also close. To make

the device capable of vacuuming again, set up the de-

vice, switch it off, wait 5 seconds and then switch it on

again.

Blower function

The blower function can be used to clean areas that are

difficult to reach or where vacuuming is not possible,

e.g. leaves in a gravel bed.

Insert the suction hose into the blower connection.

The blower function is now activated.

Illustration M

Interrupting operation

1. Set the trigger to "0 OFF".

The device is switched off.

2. Variant 1: Place the handle of the suction hose in the

intermediate parking position.

Illustration N

Variant 2: Attach the floor nozzle in the parking po-

sition.

Illustration O

Ending operation

1. Set the trigger to "0 OFF".

The device is switched off.

2. Pull out the mains plug.

3. Remove the device head.

Illustration B

4. Empty the container.

Illustration Q

5. Storage possibility:

Illustration T

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher WD 2-18 Battery Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info