Bedienungsanleitung Karcher WD 6 P (Seite 9 von 92) (Alle Sprachen)

803393

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

English 9

Note

For versions with stainless steel tubes, remove the pro-

tective cover before initial startup.

Initial startup

Inserting the filter bag

1. Fully unfold the filter bag.

2. Attach the filter bag to the device connection and

press it on firmly.

Illustration F

3. Fit and lock the device head.

Illustration G

Installing the hose, pipes, floor nozzle

1. Connect the suction hose.

Illustration H

2. Connect the suction hose to the handle.

Illustration I

Note

For convenient vacuuming in confined spaces, the han-

dle can be removed, and the accessories plugged di-

rectly onto the suction hose.

To release the handle, the grey areas on both sides of

the handle must be pressed, and the handle pulled from

the hose.

3. Connect the floor nozzle to the suction pipes.

Use the position with the brush strips extended to

vacuum dry dirt.

Use the position with squeegees extended to

suck up damp dirt / water.

Illustration J

Starting up the device

1. Plug the mains plug into the socket.

Illustration K

Devices without a socket

2. Set the trigger into the desired position.

Illustration L

Position "1 ON": The suction / blowing function is

activated.

Position "0 OFF": The device is switched off.

Devices with a socket

3. Set the trigger into the desired position.

Illustration M

"MAX" position: The suction / blowing function is

activated.

MAX position : When the power tool is con-

nected, the suction is activated automatically.

Position "0 OFF": The device is switched off.

Note

As long as the device is supplied with power, the device

socket can be used as a power source.

Note

Limited for Switzerland only: The socket outlet shall on-

ly be used during operation in dry condition.

Operation

ATTENTION

Flat pleated filter missing

Device damage

Always work with the flat pleated filter inserted.

Note

Pay attention to the latest part numbers when purchas-

ing and installing filter bags and flat pleated filters.

Information on accessories and spare parts can be

found at www.kaercher.com.

Dry vacuuming

ATTENTION

Vacuuming cold ashes

Device damage

Only vacuum cold ash with an ash pre-separator.

ATTENTION

Defective or wet flat pleated filter

Device damage

Before initial startup, check the flat pleated filter for

damage and replace it if necessary.

Only vacuum with a dry flat pleated filter.

Note

Replace the filter bag in good time, as a filter bag that is

too full could be damaged. The fill degree of the filter

bag depends on the amount of dirt vacuumed. The filter

bag should be replaced more frequently when vacuum-

ing fine dust, sand, etc.

Wet vacuuming

ATTENTION

Wet vacuuming with a filter bag

Device damage

Do not use a filter bag when vacuuming wet.

ATTENTION

Operation with full container

When the container is full, a float switch closes the suc-

tion opening and the device runs at a higher speed.

Switch off the device immediately and empty the con-

tainer.

Note

If the device falls over, the float can also close. To make

the device capable of vacuuming again, set up the de-

vice, switch it off, wait 5 seconds and then switch it on

again.

Working with power tools (only for devices

with a built-in socket)

몇CAUTION

Unintentional starting of the power tool

Injury or property damage

Make sure that the power tool is ready for operation as

soon as it is connected to the device socket.

Note

Depending on the model selected, an adapter or an

adapter and a thin tool hose are included in the scope

of delivery.

1. Connect the suction hose.

Illustration H

2. If necessary, the adapter can be adjusted to the con-

nection diameter of the power tool with a suitable

tool.

3. Option A) Put the adapter on the handle of the suc-

tion hose. Connect the suction hose to the adapter

on the power tool.

Option B) For more flexibility when working, connect

the adapter to the thin tool hose and the handle of

the suction hose and connect it to the power tool.

Option C) With some power tools, the handle of the

suction hose can be connected directly to the power

tool.

Illustration N

4. Plug the mains plug of the power tool into the device

socket.

Illustration O

5. Set the trigger to MAX Set.

The power can be regulated using the rotary switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher WD 6 P Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info