Bedienungsanleitung Katadyn Pocket (Seite 4 von 6) (Englisch)

522424

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

3) Hold the filter upright and begin pumping the handle in a slow, steady manner. Make sure

the input hose is not kinked.

4) After filling water container with filtered water, remove bottle clip from container and input

hose from water source. Continue pumping to remove remaining water from pump body.

5) Store the unit in the carry bag. To prevent the possibility of cross contamination remove the

output hose with the clip and store separately in the re-sealable bag inside the carry bag.

*Note: Before each use, pump and discard a small amount (0.2 litres) of water to remove stale taste.

Field Performance Tips

The Katadyn Pocket is designed to remove bacteria and protozoan cysts such

as Legionella, Giardia and Cryptosporidium. To extend ceramic life, always use the best

water source available. Keep the input prefilter clean and off the bottom. In heavy sediment con-

ditions, wrap a coffee filter or bandanna around the input prefilter. Where possible, place untreat-

ed water in container and wait for sediment to settle out until water appears clear - then filter from

water above the sediment.

Maintain your Katadyn water system to keep it operating smoothly.

1) If handle is hard to push:

Clogged filter pores. If the filter pores of the ceramic are clogged, the ceramic needs

to be cleaned. Never use force when pumping. Unscrew the pump base counter- clockwise

from the lower end of the filter housing and remove the plastic sleeve by pulling it down-

wards. Clean the ceramic element by brushing it with the supplied cleaning pad until the

light, originally color appears again. Be careful not to have unfiltered water touching the

filter output. Push the plastic sleeve over the ceramic element. Apply a drop of silicone

lubricant on the thread of the pump base. Tighten the pump base clockwise.

2) Lubricate pump handle o-ring. Silicone Silicone lubricant is provided with your new

unit. Unscrew the handle collar on the upper part of the filter element counter clockwise and

remove the pump handle. (Figure 1-1) Clean excess build-up from black rubber o-ring on

bottom of handle. Place a small amount of silicone lubricant on the thread of the filter

element. Re-assemble.

3) If unit pumps easily, but no water flow:

Make sure prefilter is submerged.

Make sure that input hose is not blocked or pinched.

Hold the filter vertically until water flows.

4) Prefilter: Rinse the prefilter in water to remove any particles that may be caught in the

strainer.

5) Storage: Your Katadyn water system comes with a carry bag for storage. To prevent the

possibility of cross contamination remove the output hose with the bottle clip and store

separately in the re-sealable bag inside the carry bag.

8013888-3 Pocket Manual Content EU 11-sprachig_Manual EU 19.09.2012 08:32 Seite 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Katadyn Pocket Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Katadyn Pocket

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info