Bedienungsanleitung Katadyn PowerSurvivor 160E (Seite 10 von 36) (Englisch)

522391

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation Procedures

Although every installation has its custom as-

pects, the following general instructions should

be useful to the typical installer. Refer to

Figure A-1 (in the Appendix) for information on

part identification and system connections.

1. Install Pump: After reading the

comments on the preceding pages, decide on

a location for the pump and drive assembly. It

should be mounted with the pump and drive

side by side horizontally. The reason for this

requirement is to avoid two problems:

• If the pump develops a seawater leak

and is located directly above the drive

assembly, the drive assembly and/or

electric motor may be damaged (Figure

3, left).

• If the drive assembly develops an oil leak and is located directly above the pump, oil

may find its way into the pumping system and damage the membrane (Figure 3, right).

We recommend securely thru-bolting the pump/drive assembly to a sturdy bulkhead or platform,

using corrosion-resistant 1/4" fasteners with flat washers (See Figure A-1). Pick a location that

allows ample space for routing the required hoses and electrical wires to the pump and motor.

2. Connect Electrical Power to

Pump

: To provide 12 (or 24) VDC

electric power to the motor, use a minimum

of 10 gauge stranded copper wire at 12

VDC (14 gauge / 24 VDC). We recommend

8 gauge or larger wire at 12 VDC (12

gauge / 24 VDC) for distances over

20 feet. Tinned, stranded copper wire is

preferred for marine installations and is

available in most marine hardware stores.

Figure 4 shows a typical electrical power

configuration.

Basic Electrical Diagram

Fuse and Circuit

Breaker:

12 V = 30 A

24 V = 15 A

Terminal

Strip

white

red

black

Dimension of the cable:

10 gauge / 12 V

14 gauge / 24 V

3. Mount Prefilter Assembly

and

12 V or 24 V

Battery or Power

Source

Figure 4

3-Way Valve:

Lightly coat the male

threads of the middle port of the pre filter 3-way valve with a non-hardening, paste-type thread

sealant (e.g., Permatex

) to assure an airtight seal. (Note: Teflon tape is not recommended.)

1. Carefully thread the middle port of the pre filter 3-way valve into the “IN” port of the pre

filter housing. Do not over tighten this connection. When assembled correctly, the long

axis of the 3-way valve should be vertical (See Figure A-1).

2. Fasten the supplied right-angled mounting bracket for the pre filter assembly to a

bulkhead. Orient it so the pre filter assembly will be vertical, with the bowl underneath.

We recommend that it be thru-bolted with corrosion-resistant hardware.

3. Screw the top of the pre filter housing to the bracket with the supplied screws. One port

of the pre filter 3-way valve should project above the housing through the notch in the

mounting bracket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Katadyn PowerSurvivor 160E Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Katadyn PowerSurvivor 160E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info