631715
15
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
15 of 56
5.1.4 Installing the Cable Gland and Mounting Plate
Tip
If you have previously used a Kathrein HDM140/141 jointed tripod mast or another mast with a diameter of
34mm, you can continue using the existing through hole in the roof.
Fig.A Fig.B
1 2
3
O-Ring Adhesive Arrow in the direction of travel
1. In the centre of the intended position of the turntable, drill the opening for the cable gland with a circular cutter of
Ø38 mm .
2. Deburr the hole with a round le or emery paper.
3. Provisionally insert the roof duct into the drilled hole (Fig.A).
4. Place the mounting plate on the roof of the vehicle such that the centre hole is positioned centrally to the cable gland.
The arrow symbol must be visible from above and point forwards in the direction of travel of the vehicle (Fig.B).
5. Mark the positions of the six fastening holes on the vehicle roof in a pitch circle.
Tip
The size of the holes and the choice of fastening screws to be used (not included in the scope of delivery)
depend on the type and thickness of the materials used in the roof structure. If the roof panelling (plastic
roofs) is sufciently strong, it is recommended to always use round head screws, plain washers and self-
locking nuts to secure the glued mounting plate.
6. If the roof panel material is very thin and does not provide adequate holding power within the insulation material,
make through holes of Ø5.5 mm into the interior of the vehicle and use galvanised M5 round head screws of suf-
cient length.
Make sure that you use a sufciently strong support that can withstand the bolt tensile forces (large plain washer or a
complete reinforcing plate).
Fig.C
1
2
3
*
)
*
)
*
)
*
)
Adhesive area between the two
grooves
Alternative roof fastening
Washer*)
*
)
Not included in the scope of delivery
7. Create the holes necessary to secure the mounting plate (Fig.C).
8. In addition to the screw connection, the mounting plate and roof duct must be bonded to the roof with adhesive and
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

kathrein-cap-650---mobiset-3-twin

Suche zurücksetzen

  • Habe den Fehler 04. kann leider nichts finden was es sein kann. Könnten Sie mir sagen was es ist Eingereicht am 23-9-2017 09:53

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kathrein CAP 650 - MobiSet 3 Twin wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kathrein CAP 650 - MobiSet 3 Twin

Kathrein CAP 650 - MobiSet 3 Twin Bedienungsanleitung - Deutsch - 56 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info