Bedienungsanleitung Kathrein CAP 950 - MobiSet 3 Twin (Seite 15 von 52) (Englisch)

631713

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

15 of 52

3. Provisionally insert the roof duct into the drilled hole (Fig.A).

4. Place the mounting plate on the roof of the vehicle such that the centre hole is positioned centrally to the cable gland.

The arrow symbol ③ must be visible from above and point forwards in the direction of travel of the vehicle (Fig.B).

5. Mark the positions of the six fastening holes on the vehicle roof in a pitch circle.

Tip

The size of the holes and the choice of fastening screws to be used (not included in the scope of delivery)

depend on the type and thickness of the materials used in the roof structure. If the roof panelling (plastic

roofs) is sufciently strong, it is recommended to always use round head screws, plain washers and self-

locking nuts to secure the glued mounting plate.

6. If the roof panel material is very thin and does not provide adequate holding power within the insulation material,

make through holes of Ø5.5 mm into the interior of the vehicle and use galvanised M5 round head screws of suf-

cient length.

Make sure that you use a sufciently strong support that can withstand the bolt tensile forces (large plain washer or a

complete reinforcing plate).

Fig.C

)

① adhesive area between the

grooves

② alternative roof fastening

③ washer*)

)

Not included in the scope of delivery

7. Create the holes necessary to secure the mounting plate (Fig.C).

8. In addition to the screw connection, the mounting plate and roof duct must be bonded to the roof with adhesive and

sealed. This is done using the DEKAsyl MS adhesive sealant supplied, which is ideally suited for this purpose due to

its broad range of adhesion. Please note the following points:

– Before you start working with the DEKAsyl MS adhesive sealant, it is essential that you have carefully read

through the safety data sheet for the DEKAsyl MS adhesive sealant and the technical data sheet in this

installation manual!

– The prerequisite for good adhesive properties is a clean, dry and grease-free substrate. Therefore, clean the

roof surface with a suitable cleaning agent within a circumference of 17cm around the drilled hole and allow the

surface to dry thoroughly.

– If the surface is painted, ensure that the paint nish is sufciently well bonded to the substrate.

– If the coat of paint is already loose or peeling, remove it down to a stable layer in the area to which the adhesive

will bond. If you have any doubts concerning the adhesive properties, consult a paint and lacquer specialist or the

manufacturer of your vehicle.

9. The procedure for gluing the mounting plate is as follows:

Fig.D

Adhesive area

within the grooves

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kathrein CAP 950 - MobiSet 3 Twin Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kathrein CAP 950 - MobiSet 3 Twin

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info