631745
6
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
Note: During the initialisation of the channel unit, an
indicator on the top-right side flashes for a few
seconds:
In case of a faulty entry, the flashing continues.
Possible faults:
Wrong entry of the input frequency or symbol rate.
General fault of the reception system.
935.2155/D/0705/2.4e
Setting instructions
Adjustment of the DVB channel unit is carried out via the
control unit of UFG 308 or UFG 312. Required software
version of the control unit: UFO 385: at least 6.20
UFO 387: at least 6.40.
For adjustment, it is necessary to connect the channel
unit with the control unit. The keys mentioned below are
on the control unit. (For explanations regarding their
functions, refer to the instructions valid for the base units
UFG 308, UFG 312, UFG 316).
The parameter to be set is selected with the keys „“ or
“. The selected parameter flashes.
After all parameters have been set,save the setting by
pressing„M“ inthe
EEPROM
ofthe channelunit.
1. Selecting the input frequency
The input frequency is selectable between 950 MHz and
2150 MHz in MHz steps with the keys „+“ or „-“.
Inp. 2004 MHz
22,000 MS/s 5/6
Outp. S21 306.00 MHz
6,111 MS/s 64 QAM
Changing the input frequency by numeric character entry
is also possible:
1. Press the keys „“ and „“ at the same time.
2. Use the key „“ to select the desired digit.
3. Change the frequency with the keys „+“ or „-“.
4. Return to standard operation by pressing the keys
“ and „“ at the same time.
The symbol rate can be adjusted in 0.1 MS/s steps with
the keys „+“ or „-“.
Partly changing the input symbol rate in 0.001 MS/s
steps is also possible (Refer in this connection to Sect.
1/Sub-section 1-4).
The code rate (second line of the display; figure value e.
g. 5/6) and the output symbol rate (fourth line of the
display) are automatically determined.
If the fourth line of the display does not show the output
symbol rate but indicates „zu hoch“ (too high) or „zu
niedrig“ (too low), it is necessary to change the QAM
stages (see Sect. 4, selection of the QAM stages).
**** UFO 385 ****
SNR = 15.2 dB
< back to: sup-menu >
Inp. 2004 MHz *
22.000 MS/s
Outp. S21 306.00 MHz
-.— MS/s 64 QAM
2. Selecting the input symbol rate
Inp. 2004 MHz
22,000 MS/s
Outp. S21 306.00 MHz
6,111 MS/s 64 QAM
After the parameter „input frequency“ has been selected
and the button was pressed, the signal-to-noise-ra-
tio „SNR“ is shown in the sub-menu.
For the SNR display it is required that the channel unit
accepts the input signal (the indicator stops flashing).
In order to ensure trouble-free operation, the SNR should
be 7 dB
Back to the sub-menu with key .
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kathrein UFO 387 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info