Bedienungsanleitung Kathrein UFZ 130 (Seite 2 von 2) (Deutsch, Englisch)

631733

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

936.4438/-/ZWT/0512/de - Technische Änderungen vorbehalten! Technical data subject to change.

Internet: www.kathrein.de

KATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 • P.O. Box 100 444 • 83004 Rosenheim • GERMANY • phone +49 8031 184-0 • Fax +49 8031 184-306

Features

Technical Speciﬁ cations

Electronic equipment is not household waste, sin accordance

with directive 2002/96/EC OF THE EUROPEAN PARLIAMENT

AND THE COUNCIL dated 27

January 2003 on used

electrical and electronic equipment, it must be disposed of

properly. At the end of its service life, take this unit for disposal

at a designated public collection point.



Supports the Wireless Standards IEEE 802.11b/g/n

with a data rate up to 150 Mbps



Easy installation via the receiver menu,

no additional software required



Rotating antenna: 90° in the vertical direction

and 180° in the horizontal direction



Supports 64/128-bit WEP, WPA

and WPA2 encryption



Connection indicator LED



Power supply via the receiver's USB port



Suitable for the receivers:

UFS 913 from software version V1.01,

UFS 923 from software version V1.03,

UFS 925, UFS 935



For indoor installation



Type UFZ 130

Part no. 20410041

Standard IEEE802.11b, 802.11g, 802.11n

Connection USB 2.0 type A

Data rates

11b: 1/2/5.5/11 Mbps

11g: 6/9/12/24/36/48/54 Mbps

11n (20 MHz):

MCS 0-7 (up to 72 Mbps)

11n (40 MHz):

MCS 0-7 (up to 150 Mbps)

Operating temperature °C +0 to +40

Unit dimensions

(W x H x D)

mm 15 x 155 x 15

Connection

Connect the WLAN/USB adaptor to a free USB 2.0 port on your

Kathrein receiver. On most devices this can be found at the rear.

Please note that this procedure is currently available only for the

receivers listed above and the software versions shown.

Setting up

If you have not yet done so, now switch your receiver on.

Press the menu button to call up the main menu. In the menu,

select “Interfaces” and conﬁ rm with “OK”. Now select “Ethernet

Settings” and again conﬁ rm with “OK”. The following on-screen

display appears:

Use the arrow buttons to select the setting “On”. To activate the

WLAN function you must then restart the receiver. After the restart,

call up this menu (Main menu - Interfaces - Ethernet Settings)

once again. In the menu, select the “WLAN Conﬁ guration” line

and conﬁ rm with “OK”. The display lists all the wireless (WLAN)

networks that were found. In the menu, select the desired

wireless network and conﬁ rm with “OK”. Now you must input your

network PIN.

Select the required settings here, according to your circumstances.

You can then select “Test Connection” to test your settings, and

“Save” to save them. After you have successfully made your

settings, you will see the following on-screen display in the lower

part of the “Ethernet Settings” menu (example):

To input your network PIN, call up the menu (Main menu -

Interfaces - Ethernet Settings) once again. In the menu, select

the “IP Conﬁ guration” line and conﬁ rm with “OK”. The following

on-screen display appears (example):

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kathrein UFZ 130 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info