Bedienungsanleitung Kaysun AKAY-CF 35 DR10 (Seite 23 von 36) (Englisch)

771407

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Wedge

Move to left or right

 Page 23 

DO NOT INTERTWINE SIGNAL CABLE

WITH OTHER WIRES

While bundling these items together, do not intertwine or

cross the signal cable with any other wiring.

2. Using adhesive vinyl tape, attach the drain hose to

the underside of the refrigerant pipes.

3. Using insulation tape, wrap the signal wire, refrigerant

pipes, and drain hose tight

DO NOT WRAP ENDS OF PIPING

When wrapping the bundle, keep the ends of the piping

unwrapped. You need to access them to test for leaks

at the end of the installation process (refer to Electrical

Checks and Leak Checks section of this manual).

Step 8: Mount indoor unit

If you installed new connective piping to the outdoor

unit, do the following:

1. If you have already passed the refrigerant piping

through the hole in the wall, proceed to Step 4.

2. Otherwise, double-check that the ends of the

refrigerant pipes are sealed to prevent dirt or foreign

materials from entering the pipes.

3. Slowly pass the wrapped bundle of refrigerant pipes,

drain hose, and signal wire through the hole in the

wall.

4. Hook the top of the indoor unit on the upper hook of

the mounting plate.

5. Check that unit is hooked rmly on mounting by

applying slight pressure to the left and right-hand

sides of the unit. The unit should not jiggle or shift.

6. Using even pressure, push down on the bottom half of

the unit. Keep pushing down until the unit snaps onto

the hooks along the bottom of the mounting plate.

7. Again, check that the unit is rmly mounted by

applying slight pressure to the left and the right-hand

sides of the unit.

If refrigerant piping is already embedded in the wall,

do the following:

1. Hook the top of the indoor unit on the upper hook of

the mounting plate.

2. Use a bracket or wedge to prop up the unit, giving you

enough room to connect the refrigerant piping, signal

cable, and drain hose.

3. Connect drain hose and refrigerant piping (refer

Refrigerant Piping Connection section of this manual

for instructions).

4. Keep pipe connection point exposed to perform the

leak test (refer to Electrical Checks and Leak Checks

section of this manual).

5. After the leak test, wrap the connection point with

insulation tape.

6. Remove the bracket or wedge that is propping up the

unit.

7. Using even pressure, push down on the bottom half of

the unit. Keep pushing down until the unit snaps onto

the hooks along the bottom of the mounting plate.

UNIT IS ADJUSTABLE

Keep in mind that the hooks on the mounting plate are

smaller than the holes on the back of the unit. If you nd

that you don't have ample room to connect embedded

pipes to the indoor unit, the unit can be adjusted left or

right by about 30-50mm (1.25-1.95in), depending on the

model.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun AKAY-CF 35 DR10 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun AKAY-CF 35 DR10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info