Bedienungsanleitung Kaysun Aquantia Hidraulic Kit - KHHP-BI (Seite 35 von 45) (Englisch)

771433

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

Page 35 

BEFORE PERFORMING ANY

ELECTRICAL WORK, READ

THESE REGULATIONS

1. All wiring must comply with local and

national electrical codes, regulations and

must be installed by a licensed electrician.

2. All electrical connections must be made

according to the Electrical Connection

Diagram located on the panels of the

indoor and outdoor units.

3. If there is a serious safety issue with the

power supply, stop work immediately.

Explain your reasoning to the client, and

refuse to install the unit until the safety

issue is properly resolved.

4. Power voltage should be within 90-110%

of rated voltage. Insucient power

supply can cause malfunction, electrical

shock, or re.

5. If connecting power to xed wiring,

install a surge protector and main power

switch with a capacity of 1.5 times the

maximum current of the unit.

6. If connecting power to xed wiring, a

switch or circuit breaker that disconnects

all poles and has a contact separation of

at least 1/8in (3mm) must be

incorporated in the xed wiring. The

qualied technician must use an

approved circuit breaker or switch.

7. Only connect the unit to an individual

branch circuit outlet. Do not connect

another appliance to that outlet.

Wiring

13. Make sure that you do not cross your

electrical wiring with your signal wiring.

This may cause distortion and

interference.

14. The unit must be connected to the

main outlet. Normally, the power supply

must have a impedance of 32 ohms.

15. No other equipment should be

connected to the same power circuit.

16. Connect the outdoor wires before

connecting the indoor wires.

11. If the unit has an auxiliary electric heater,

it mustbe installed at least 1 meter (40in)

away from any combustible materials.

12.To avoid getting an electric shock, never

touch the electrical components soon

after the power supply has been turned

o. After turning o the power, always

wait 10 minutes or more before you touch

the electrical components.

8. Make sure to properly ground the air

conditioner.

9. Every wire must be rmly connected.

Loose wiring can cause the terminal to

overheat, resulting in product

malfunction and possible re.

10. Do not let wires touch or rest against

refrigerant tubing, the compressor, or

any moving parts within the unit.

WARNING

BEFORE PERFORMING ANY

ELECTRICAL OR WIRING WORK,

TURN OFF THE MAIN POWER TO

THE SYSTEM.

Note on Air switch

When the maximum current of the air

conditioner is more than 16A, an air switch or

leakage protection switch with protective

device shall be used(purchased seperately) .

When the maximum current of the air

conditioner is less than 16A, the power cord

of air conditioner shall be equipped with

plug (purchased seperately) .

Wiring

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun Aquantia Hidraulic Kit - KHHP-BI Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun Aquantia Hidraulic Kit - KHHP-BI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info