Bedienungsanleitung Kaysun Aquantia PRO Monobloc - KHP-MO (Seite 36 von 80) (Englisch)

771521

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

A main switch or other means of disconnection, having a contact separation in all poles, must be incorporated in the

fixed wiring in accordance with relevant local laws and regulations. Switch off the power supply before making any

connections. Use only copper wires. Never squeeze bundled cables and make sure they do not come in contact with

the piping and sharp edges. Make sure no external pressure is applied to the terminal connections. All field wiring and

components must be installed by a licensed electrician and must comply with relevant local laws and regulations.

The field wiring must be carried out in accordance with the wiring diagram supplied with the unit and the instructions

given below.

Be sure to use a dedicated power supply. Never use a power supply shared by another appliance.

Be sure to establish a ground. Do not ground the unit to a utility pipe, surge protector, or telephone ground. Incomplete

grounding may cause electrical shock.

Be sure to install a ground fault circuit interrupter (30 mA). Failure to do so may cause electrical shock.

Be sure to install the required fuses or circuit breakers.

WARNING

9.7.2 Wiring overview

The ground fault circuit interrupter must be a high- speed type breaker of 30 mA (<0.1 s).

NOTE

This unit is equipped with an inverter. Installing a phase advancing capacitor not only will reduce the power factor improve-

ment effect, but also may cause abnormal heating of the capacitor due to high-frequency waves. Never install a phase

advancing capacitor as it could lead to an accident.

The illustration below gives an overview of the required field wiring between several parts of the installation. Refer also to "8

Typical application examples".

Secure the electrical wiring with cable ties as shown in figure so that it does not come in contact with the piping, particularly

on the high-pressure side.

Make sure no external pressure is applied to the terminal connectors.

When installing the ground fault circuit interrupter make sure that it is compatible with the inverter (resistant to high frequency

electrical noise) to avoid unnecessary opening of the ground fault circuit interrupter.

Fix cables so that cables do not make contact with the pipes (especially on the high pressure side).

9.7.1 Precautions on electrical wiring work

9.6 Water piping insulation

9.7 Field wiring

The complete water circuit including all piping, water piping must be insulated to prevent condensation during cooling operation

and reduction of the heating and cooling capacity as well as prevention of freezing of the outside water piping during winter. The

insulation material should at least of B1 fire resistance rating and complies with all applicable legislation. The thickness of the

sealing materials must be at least 13 mm with thermal conductivity 0.039 W/mK in order to prevent freezing on the outside water

piping.

If the outdoor ambient temperature is higher than 30°C and the humidity is higher than RH 80%, then the thickness of the

sealing materials should be at least 20 mm in order to avoid condensation on the surface of the seal.

NOTE

During filling, it might not be possible to remove all air in the system. Remaining air will be removed through the

automatic air purge valves during the first operating hours of the system. Topping up the water afterwards might be

required.

The water pressure indicated on the manometer will vary depending on the water temperature (higher pressure at

higher water temperature). However, at all times water pressure should remain above 0.3 bar to avoid air entering

the circuit.

The unit might drain-off too much water through the pressure relief valve.

Water quality should be complied with EN 98/83 EC Directives.

Detailed water quality condition can be found in EN 98/83 EC Directives.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun Aquantia PRO Monobloc - KHP-MO Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun Aquantia PRO Monobloc - KHP-MO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info