Bedienungsanleitung Kaysun COMPAK KHPA (Seite 16 von 64) (Englisch)

771578

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

5 - POSITIONING

The installation has been implemented by qualified technical

personnel only and that the instructions contained in the

present manual and the local regulations in force have been

adhered to.

Choose the installation place according to the following

criteria:

 customer approval

 Internal

 in a dry room/compartment where the temperature cannot

fall below 0 degrees

 guarantee good unit operation

 safe accessible position

 enough space for installation and maintenance shall be

preserved.

 the air inlet and outlet should be free from obstacles and

strong wind.

 the base surface should be flat, surface should be inclined

no more than 2°and able to bear the weight of the unit and

suitable for installing the unit without increasing noise or

vibration.

 the operation noise and air flow expelled shall not affect

neighbors.

 If the unit has to be installed on a metal part of building,

make sure the well electric insulation which should meet

the relevant local electric standard.

 use of air from heated rooms could penalise the heating

performance of the building

 the unit must be securely fixed, elsewise, noise and

shaking may be resulted.

 make sure that there’s no obstacle around the unit.

The external air temperature must also be considered when

installing this unit, in heat pump mode the external air

temperature must be above -7°C and below 43°C. If the

externalair temperature falls outside these upper and lower

limits, the electrical elements will activated to meet the hot

water demand and the heat pump does not operate.

The unit should be located in an area not subject to freezing

temperatures. The unit located in unconditioned spaces(i.e.,

garages, basements, etc.) may require the water piping,

condensate piping, and drain piping to be insulated to shelter

against freezing.

Installing the unit in any of the following places may lead to

malfunction:

 The site contains mineral oils such as cutting lubricant

 Seaside where the air contains much salt.

 Hot spring area where corrosive gases exist, e.g., sulfide

gas.

 Factories where the power voltage fluctuates seriously.

 The place with direct sunlight and other heat supplies. If

there’s no way to avoid these, please install a covering.

 Place like kitchen where oil permeates.

 Place where strong electromagnetic waves exist.

 Place where flammable gases or materials exist.

 Place where acid or alkali gases evaporate.

5.1 - INSTALLATION REQUIREMENTS 5.2 - CONSIDER SOUND EMISSIONS

Noise levels could represent an inconvenience if installed in

areas that require extreme silence, example near bedrooms.

Unit dimension / Functional spaces

Unit 190

190S (with solar)

300

300S (with solar)

Width A 560 650

Height B1830 1930

Diameter C 560 650

Functional

spaces

D = 600 = 600

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun COMPAK KHPA Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info