Bedienungsanleitung Kaysun KEM-05 DVN1 (Seite 12 von 48) (Englisch)

771470

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

5. UNIT INSTALLATION

5.1 Before installation

Before installation

Be sure to confirm the model name and the serial number of the unit.

Handling

Due to relatively large dimensions and heavy weight, the unit should

only be handled using lifting tools with slings. The slings can be fitted

into foreseen sleeves at the base frame that are made specifically

for this purpose.

CAUTION

■ To avoid injury, do not touch the air

inlet or aluminium fins of the unit.

■ Do not use the grips in the fan

grills to avoid damage.

■ The unit is top heavy! Prevent the

unit from falling due to improper

inclination during handling.

5.2 Selecting the installation site

WARNING

Unit A(mm)

5-16kW ≥2000

Make sure there is enough room to do the installation

■ Set the outlet side at a right angle to the direction of the wind.

Strong wind

Blown air

Strong wind

Blown air

■ Be sure to provide for adequate measures in order to

prevent that the unit be used as a shelter by small animals.

■ Small animals making contact with electrical parts can cause

malfunctions, smoke or fire. Please instruct the customer to

keep the area around the unit clean.

1 Select an installation site where the following conditions

are satisfied and one that meets with your customer's approval.

- Places that are well-ventilated.

- Places where the unit does not disturb next-door neighbours.

- Safe places which can bear the unit's weight and vibration

and where the unit can be installed at an even level.

- Places where there is no possibility of flammable gas or product

leak.

- The equipment is not intended for use in a potentially

explosive atmosphere.

- Places where servicing space can be well ensured.

- Places where the units' piping and wiring lengths come within

the allowable ranges.

- Places where water leaking from the unit cannot cause

damage to the location (e.g. in case of a blocked drain pipe).

- Places where rain can be avoided as much as possible.

- Do not install the unit in places often used as a work space.

In case of construction work (e.g. grinding etc.) where a lot of

dust is created, the unit must be covered.

- Do not place any objects or equipment on top of the unit (top

plate)

- Do not climb, sit or stand on top of the unit.

- Be sure that sufficient precautions are taken in case of refrigerant

leakage according to relevant local laws and regulations.

2 When installing the unit in a place exposed to strong wind,

pay special attention to the following.

Strong winds of 5 m/sec or more blowing against the unit's air

outlet causes a short circuit (suction of discharge air), and this

may have the following consequences:

- Deterioration of the operational capacity.

- Frequent frost acceleration in heating operation.

- Disruption of operation due to rise of high pressure.

- When a strong wind blows continuously on the front of the unit,

the fan can start rotating very fast until it breaks.

Refer to the figures for installation of this unit in a place where

the wind direction can be foreseen.

■ Turn the air outlet side toward the building's wall, fence or screen.

3 Prepare a water drainage channel around the foundation, to drain

waste water from around the unit.

4 If water does not easily drain from the unit, mount the unit on a

foundation of concrete blocks, etc. (the height of the

foundation should be about 100 mm (3.93 in.).

5 If you install the unit on a frame, please install a waterproof plate

(about 100 mm) on the underside of the unit to prevent water from

coming in from the low side.

6 When installing the unit in a place frequently exposed to

snow, pay special attention to elevate the foundation

as high as possible.

7 If you install the unit on a building frame,

please install a waterproof plate (field supply)

(about 100 mm.) on the underside of the

unit in order to avoid drain water dripping.

(See figure).

NOTE

Unit is top heavy!

Try not to install on the building frame.

5.2.1 Selecting a location in cold climates

NOTE

When operating the unit in cold climates, be sure to

follow the instructions described below.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun KEM-05 DVN1 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun KEM-05 DVN1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info