771475
18
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
5.4.4 Application 4
Space cooling and heating application with a standard controller (or optional wired controller) connected to the unit. Heating is provided
through floor heating loops. Cooling is provided through the fan coil units only. The 3-way valve is used to change the direction of water flow
when the operation mode changed.
4
T1
T2
12
Tn
15
1
M1
M2
Mn
10
FCU1
FCU2
FCUn
5
9.1
11
16
12
M
9
2
3
9.2
13
6
7
8
FHL1
FHL2
FHLn
1
outdoor unit
10
expansion vessel (field supply)
2
Y-shape filter
11
Pump 2: outside circulation pump (field supply)
3
shut-off valve (field supply)
12
collector (field supply)
4
wired controller (optional)
13
mixing station (field supply)
5
non-return valve (field supply)
15
by-pass valve (field supply)
6
drain valve (field supply)
16
Motorised 3-way valve (field supply, field control)
7
fill valve (field supply)
FHL 1...n
floor heating loop
8
buffer tank (field supply)
FCU 1...n
fan coil units
9 balance tank (field supply)
9.1 air purge valve
9.2 drain valve
NOTE
If the volume of balance tank (9) larger than 30L, the buffer tank(8) is unnecessary, otherwise the buffer tank(8)
B
should be installed and the total volume of buffer tank and balance tank should larger than 30L.The drain valve (6)
should be installed at the lowest position of the system. An independent backup heater can be selected and installed
in the door, which can provide additional heating source and ensure better performance of the system when the
inlet
M
ambient temperature is low.
The 3-way valve control requires field control, the unit does not provide control function.
In normal condition, port A should be opened, while signal sent to the 3-way valve (16), port A will be closed and port B will be opened.
When in cool mode, ON signal will sent to the 3-way valve (16), the cold water will flow through port inlet to port B, and port B should
connect to the fan coil units. While in heating mode, the hot water will flow through port inlet to port A, and port A should connect to the
floor heating loops. In this way, all the water from the unit will flow through the floor heating loops and thus ensure better performance of
the floor heating.
A
17
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kaysun KEM-14 DTN wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kaysun KEM-14 DTN

Kaysun KEM-14 DTN Bedienungsanleitung - Holländisch - 48 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info