Bedienungsanleitung Kaysun KPC-52 DR13 (Seite 24 von 40) (Englisch)

771435

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Step 3:

Drill wall hole for connective piping

1. Determine the location of the wall hole

based on the location of the outdoor unit.

2. Using a 65mm (2.5in) or 90mm(3.54in)

(depending on models )core drill, drill a

hole in the wall. Make sure that the hole

is drilled at

a slight downward angle, so

that the outdoor end of the hole is lower

than the indoor end by about 12mm (0.5in).

This will ensure proper water drainage.

3. Place the protective wall cu in the hole. This

protects the edges of the hole and will help

seal it when you nish the installation process.

CAUTION

When drilling the wall

hole, make sure to

avoid wires, plumbing,

and other sensitive

components.

Wall

IndoorOutdoor

≈ 12mm

/ 0.5 inch

Indoor Unit

Installation

Step 4:

Connect drain hose

NOTE ON DRAINPIPE INSTALLATION

•When using an extended drainpipe, tighten

the indoor connection with an additional

protection tube to prevent it from pulling

loose.

•The drainpipe should slope downward at a

gradient of at least 1/100 to prevent water

from owing back into the air conditioner.

•To prevent the pipe from sagging, space

hanging wires every 1-1.5m (39-59”).

•Incorrect installation could cause water to

ow back into the unit and ood.

The drainpipe is used to drain water away from

the unit. Improper installation may cause unit

and property damage.

CAUTION

•Insulate all piping to prevent condensation,

which could lead to water damage.

•If the drainpipe is bent or installed

incorrectly, water may leak and cause a

water-level switch malfunction.

•In HEAT mode, the outdoor unit will

discharge water. Ensure that the drain hose

is placed in an appropriate area to avoid

water damage and slippage.

•DO NOT pull the drainpipe forcefully. This

could disconnect it.

NOTE ON PURCHASING PIPES

Installation requires a polyethylene tube

(exterior diameter = 3.7-3.9cm, interior diameter

= 3.2cm), which can be obtained at your local

hardware store or dealer.

Indoor Drainpipe Installation

Install the drainpipe as illustrated in the following

Figure.

Drainpipe

connecting port

Drain hose

Pipe clasp

Insulation

Cover the drainpipe with heat insulation to

prevent condensation and leakage.

Attach the mouth of the drain hose to the

unit’s outlet pipe. Sheath the mouth of the

hose and clip it rmly with a pipe clasp.

Downward slope

1/100

1-1.5m

(39-59”)

NOTE: When connecting multiple drainpipes,

install the pipes as illustrated in the following

Figure.

≥10cm

(4”)

3. Pass the drain hose through the wall hole.

Make sure the water drains to a safe location

where it will not cause water damage or a

slipping hazard.

NOTE: The drainpipe outlet should be at least

5cm (1.9”) above the ground. If it touches the

ground, the unit may become blocked and

malfunction. If you discharge the water directly

into a sewer, make sure that the drain has a U

or S pipe to catch odors that might otherwise

come back into the house.

Page 24 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun KPC-52 DR13 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun KPC-52 DR13

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info