Bedienungsanleitung Kaysun KRE-1000DX1 (Seite 19 von 32) (Englisch)

771568

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

pag. 19

5.2 System address and network address setting

1) After first powered on, please set the system address by remote controller or wired

controller, the address range is 0-63, the indoor unit addresses of the same system

can not be repeated.

2) Display as the table.5-2, when there are different ENC1, the address setting will be dif-

ferent;

Each independent control box needs to be set an address, this address is an actual

address; when the capacity code ENC1 is selected to be E-4, this indoor unit inde-

pendent control box will produce virtual address(es) with corresponding quantity based

on the set actual address, and if an address has been an actual address or virtual

address, then this address can not be the actual address or virtual address of other

indoor unit in the same system;

For example, if there are two independent control boxes in the same system, one of

the capacity code is E, the setting actual address is 5, then according to the table.7-2

this control box will produce one virtual address as 6, and then the actual address and

the virtual address of the other independent control box can not be any one of 5, 6;

The actual address and the virtual address should less than or equal to 63.

3) The indoor unit quantity detected by outdoor unit will be the sum of the actual address

quantity and the virtual address quantity, e.g. when the capacity code of independent

control box is E, the setting actual address is 5, then it will produce virtual address 6,

and then the indoor unit quantity detected by outdoor unit will be 2.

4) The outdoor unit can not use auto addressing for to set the address for the indoor unit

without address; only the indoor unit has address then can the outdoor unit to be set

auto addressing;

5) When the independent control box system connects to the indoor unit centralized con-

troller, the actual address and the virtualaddress will be displayed on the centralized

controller, e.g. when the capacity code of independent control box is E, the setting

actual address is 5, then the actual address 5 and virtual address 6, will be displayed

on the centralized controller, that is to say, it equals to two indoor units, and the states

of four indoor units will be kept in the same;

6)The network address is the same as the indoor unit address, no need to setting sepa-

rately.

5.1 Application control

Refer to the specific manuals "AHU AHU Control box" and "Wired Controller" sup-

plied with the unit; below are explained the main instructions.

Set the PCB code of the indoor unit electric control box by different usage.

After setting, be sure to turn off the total power switch and then switch on.

The setting function can not be carried out if not to turn off the total power switch and then

switch on (SW4-2, ENC1).

5.3 - Checks before start up

Before starting the unit check the following:

• Anchorage of the unit to the ceiling.

• Connection of the air ducts.

• Connection of the earth cable.

• Fixing of all the electric terminals

SW4-2 ENC1 Corresponding Virtual Addresses Qty of Occupied

Addresses

00~D No virtual address 1

0 E-F Actual address +1 / / / / 2

00-1 Actual address +1 / / / / 2

02-4 Actual address +1 Actual address +2 Actual address +3 / / 4

Table. 5-2

Table 5-1 Capacities of SW4-2 and ENC1

SECTION 5 - SETTINGS MODULE









')#&* 

$(



')#&* 







$(



KAHU-90.4

$(

$(

$(

$(

$(

$(

$(



KAHU-200.4

$(

$(

$(

$(

$(

$(

$(



KAHU-360.4

$(





$(

$(

$(

KAHU-560.4

$(

$(

Capacity Capacity

- Function specification:

SW4-2, ENC1 - Cooling capacity setting, set the

cooling capacity of this machine (Table. 5-1).

DipSW factory settings:

SW1: 0000 (leaving the differential for thermo-off

in cooling by default at 0 ° C)

SW2: 0000

SW3: 0001 (compensation in heating 2 ° C, the

only dipSW to actually move)

SW4: 0000

SW9: 000

SW10: 00 (identifies UTA kit size)

Capacity settings:

- KRE-500DX1

(3 kW in cooling) -> 1HP -> SW4-2=0, ENC1=1

- KRE-1000DX1

(5,8 kW in cooling) -> 2HP -> SW4-2=0, ENC1=4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun KRE-1000DX1 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info