771566
11
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
7
Table 4-3 Code and Denitions
Operation lamp Flashing
times
Show on central-
ized controller
Explanation
/ / Unit is ON
/ / Unit is OFF
E2 Indoor temperature sensor
error
4E5(new protocol)
EF(old protocol)
Outdoor temperature sensor
error
6 E7 EEPROM error
8 E6 DC fan motor error
10 OFF LINE Without address
12 E1 Communication error with
ODU
14 Ip address Conict
16 EU error with sensor board
18 FC error with CO2 sensor
E9 wire controller communica-
tion failure
Ed Outdoor unit failure
NOTE: ●:Light ; ○:Extinguish ; :Quick ash
Table 4-4 Terminal Denition
CODE CN8 CN9 CN32 CN33 CN7 CN3 CN4 CN21
NAME P Q E X Y E Modbus RTU D1D2E X1X2 Indoor temp. Sensor Outdoor temp. Sensor PRO
Dry contact
(In put)
CN31 Inlet air pre-heat Signal
CN16 Force to exhaust air mode
CN26 Remote ON/OFF
Dry contact
(Out put)
CN14 Signal for ventilation fan
CN15 Alarm
CN20 Signal for inlet air Pre-heat
Communication wiring between the indoor and outdoor units
The KRE and outdoor units communicate via the RS485 serial port.
The communication wiring between the KRE and outdoor units should be connected one unit after another in a daisy chain from the out-
door unit to the nal KRE unit. And the shielded layer must be properly grounded, and a build-out resistor must be added to the last KRE
unit to enhance the stability of the communication system.
Incorrect wiring such as a star connection or a closed ring will cause instability of the communication system and system control anoma-
lies.
Use a three core shielded wire (greater than or equal to 0.75 mm2) for the communication wiring between the indoor and outdoor units.
Make sure the wiring is connected correctly. The connecting lead for this communication wire must come from the master outdoor unit.
All shielded wiring in the network are interconnected, and will eventually connect to earth at the same point “ ”.
P
Q
Outdoor
unit (Connect the shielded end of the shielded wire to
the electronic controller box sheet metal " " here)
Signalling line be-
tween outdoor units
Connecting the shielded
layer of the shielded wire
Only the last indoor unit requires add-
ing the build-out resistor at P and Q.
(open)
Indoor and out-
door units Com-
munication wire
Build-out
resistor
(P Q E)
(P Q E)
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kaysun KRE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info