Bedienungsanleitung Kaysun KRE (Seite 15 von 20) (Englisch)

771566

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

6. KRE APPLICATION

6.1 Operation principle

KRE (Heat Recovery Ventilation) employ advanced technique

and technics, the heat exchanged core forming by special paper

that be processed with chemical treatment, which could create

the optimum result in temperature, humidity and cooling recov-

ery.

High efciency heat exchanged core: When air ow formed by

exhaust air and outdoor air through the heat exchanged core in

cross way, because of temperature difference in the two sides

of at partition board, the heat transmission is occurred. In

summer, outdoor air acquire cooling from air exhaust to decrease

environment temperature; In winter, outdoor air acquire heat from

air exhaust to increase temperature, that is to say, it realizing the

energy recovery during air exhaust process to exchange the heat

in heat exchanged core to outdoor air.

6.2 Pay Attention To The Following Items Before

Operation

6.2.1. Before start-up, please clean up the duct and check

whether all air valves and devices are normal.

6.2.2. Carefully adjust the system air valves when start-up, con-

trol the current of motor in rated range.

6.2.3. Three-phase model without by-pass function, therefore the

fan would delay 30 seconds to start up.

6.2.4. Connect the wired controller

Wired controller should be installed according to wired

controller owner’s manual, installation manual (Attached in

the package box in wire controller).

7 MAINTENANCE AND UPKEEP

7.1 During early use, one should check the fan operation regu-

larly.

7.2 The cleaning regulation for air lter depend on local environ-

ment. It could be clean by vacuum dirt exhauster or water, if

heavy dust accumulates, it should use neutral detergent to

clean it, and then dry it in shady and cool place for 20 to 30

minutes and replace it.

7.3 Clean the core at least 2 years a time by vacuum dirt

exhauster to remove dust and foreign substance in the unit

assemblies, do not touch the assemblies by exhauster and

ush by water to avoid core damage.

7.4 Check the fan every half a year to maintain the well balance

of it and check whether the axletree has loosed.

8. TRIAL RUN

8.1 Please Conrm The Following Points Before

Trial Run:

8.1.1 The unit is installed correctly completed.

8.1.2 Ducting and wiring are correctly completed.

8.1.3 The drainage is smooth.

8.1.4 The heating insulation works well.

8.1.5 The ground wiring is connected correctly.

8.1.6 The power voltage ts the rated voltage of KRE.

8.1.7 There is no obstacle at the outlet and inlet of KRE.

8.2 Control The KRE By Wired controller, Operate

It According To Wired controller Owner’s Manual.

8.2.1 Whether the switch on the remote controller works well.

8.2.2 Whether the room temperature is adjusted well.

8.2.3 Whether the indicator lights normally.

8.2.4 Whether there is vibration or abnormal noise during opera-

tion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun KRE Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info