771555
9
Zoom out
Zoom in
Vorherige Seite
1/38
Nächste Seite
5
12
13
14
15
16
17
810
9
611
4
56
56
1
2
3
2
3
2
3
6
6
6
7
27-05-2019
Sets the desired water tank
temperature, ranging from
25°C to 80°C.
04:27 sun
DHW
TANK
ON
45 °C
07
Scenario 6
Group control of the hydro module.
When multiple hydro modules heat water in one water tank, the group control function of the hydro module should be used.
(For more information, please read the Installation Manual.) The group control function is only valid for the DHW mode.
Notes:
1. The group control function of the hydro module is valid for the DHW mode only.
2. Master and slave hydro modules should be set. For instructions on how to set master and slave hydro modules, see the
Installation Manual.
3. The master hydro module must be connected to a wired controller. The main wired controller can be used to set
temperature.
4. The slave hydro module can be connected to or not connected to a wired controller. The slave wired controller provides
limited functions, such as parameter query.
5. The circulating pump and water tank temperature sensor should be connected to the master hydromodule.
To enable the group control function, you need to
set the DIP switch on the main board as follows: for
the master hydro module, turn digit 11; for the slave
hydro module, turn digit 10:
ON
SW4
1 2
Group control function setting: 00
and 01: Group control function is
unavailable.
11: Group control function is
available. This hydro module is a
master hydro module. 10: Group
control function is available. This
hydro module is a slave hydro
module.
(By default, the value is 00, indicating
that a controlled group contains only
one master unit.) ON=1,OFF=0
Notes:
1. The master unit must be connected to a wired
controller. The wired controller is used to set the
desired water tank temperature.
2. The slave unit can be connected to or not
connected to a wired controller. The wired controller
of the slave unit provides the query function only.
3. The pump is controlled by the master unit. The
temperature sensor of the water tank is connected to
the master unit.
4. The wired controller connected to the master unit
is used to set the desired water tank temperature.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kaysun KWF-140 HT ACS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kaysun KWF-140 HT ACS

Kaysun KWF-140 HT ACS Bedienungsanleitung - Deutsch - 38 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info