Bedienungsanleitung Kaysun Prodigy Pro Series (Seite 20 von 41) (Englisch)

771410

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

Distance from ceiling is determinded by the

installation method.

2,3 m or more

12 cm or

 Page 20 

7. Indoor Unit Installation

Installation Instructions - Indoor

Unit

PRIOR TO INSTALLATION

Before installing the indoor unit, refer to the label on

the product box to make sure that the model number

of the indoor unit matches the model number of the

outdoor unit.

Step 1: Select installation location

Before installing the indoor unit, you must choose an

appropiate location. The following are standards that

will help you choose an appropriate location for the unit.

Proper installation locations meet the following

standards:

5Good air circulation

5Convenient drainage

5Noise from the unit will not disturb other people

5Firm and solid - the location will not vibrate

5Strong enough to support the weight of the unit

5A location at least one meter from all other

electrical devices (e.g., TV, radio, computer)

DO NOT install unit in the following locations:

Near any source of heat, steam, or combustible

gas

Near ﬂammable items such as curtains or clothing

Near any obstacle that might block air circulation

Near the doorway

In a location subject to direct sunlight

NOTE ABOUT WALL HOLE:

If there is no ﬁxed refrigerant piping:

While choosing a location, be aware that you should

leave ample room for a wall hole (see Drill wall hole

for connective piping step) for the signal cable and

refrigerant piping that connect the indoor and outdoor

units. The default position for all piping is the right side

of the indoor unit (while facing the unit). However, the

unit can accomodate piping to both the left and right.

Refer to the following diagram to ensure proper

distance from walls and ceiling:

NOTE:

• If no need the back holder to prop up the

unit:

Finishing the pipe and cable connections before

mount the indoor unit on the wall. If the installation

height is limited, 5cm from the ceiling is allowable,

but this can lower product performance. To ensure

enough space to install and remove the top air ﬁlter,

keep at least 10cm or more from the ceiling.

• Need the back holder to prop up the unit:

If connecting pipe and cable with the front panel

open, the minimum distance from ceiling is 22cm

or more, if connecting pipe and cable without front

panel (remove it), the minimum distance from ceiling

is 11cm or more.

Step 2: Attach mounting plate to wall

The mounting plate is the device on which you will

mount the indoor unit.

• Remove the screw that attaches the mounting plate

to the back of the indoor unit.

• Secure the mounting plate to the wall with the screws

provided. Make sure that mounting plate is ﬂat against

the wall.

NOTE FOR CONCRETE OR BRICK WALLS:

If the wall is made of brick, concrete, or similar material, drill

5mm-diameter (0.2in-diameter) holes in the wall and insert

the sleeve anchors provided. Then secure the mounting

plate to the wall by tightening the screws directly into the

clip anchors.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun Prodigy Pro Series Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun Prodigy Pro Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info