Bedienungsanleitung Kaysun Solar Compak KHPA2 (Seite 45 von 84) (Englisch)

771572

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

About Running

1 System Structure Figure

Unit has two kinds of heat sources: Heat pump(compressor)

and electric heater.

Unit will automatically select heat sources to heat water to the

target temperature.

2 Water Temperature Display

The temperature shown on the display depends on the upper

sensor. So it is normal that the display temperature has

reached to target temperature but compressor still running,

because the lower water temperature does not get to target

temperature.

Modes will be automatically selected by unit. manually mode

selection is unavailable.

3 Heat source will be automatically selected by unit. But manually

E-Heater operation is available.

4 Heat Source Shift

The default heating source is heat pump.If externalis range out

of heat pump, heat pump will stop running, the unit will shift

automatically to activate E-heater and show the icon LA on

the display, then if the externaltemperature goes into the

running range of heat pump again, it will stop E-heater and

shift automatically to heat pump again, and the icon LA will be

extinguished.

If the target setting water temperature is higher than Max. temp

(Heat pump), the unit will activate heat pump firstly to the Max.

temperature, then stop heat pump, activate E-heater to

continually heat water to the target temperature.

If manually activate the E-heater running mode when heat pump

running, E-heater and heat pump will work together until the

water temperature gets to target temperature.

So if want to heat quickly, please manually activate E-heater.

Note

E-heater will be activated once for the current heating progress,

if want to apply E-heater again please push

E-HEATER.

If system occurs some malfunctions, error code "E7" and , e

will be shown on the display, then heat pump will stop running,

and the unit will activate automatically E-heater as the backup heat

source, but the code "E7" and will be shown until power off.

If only use E-heater, about only 75 liters water (unit 190S) will be

heated or about only 150 liters water (unit 300S), so must set

higher target water temperature if externaltemperature is out of

heat pump running range.

Defrosting During Water-heating

In heat pump running period, if the evaporator frosted in lower

ambient temperature, the system will defrost automatically to keep

effective performance(about 3~10min). At defrosting time, the fan

motor will stop, but compressor will still run.

TCO and ATCO

The power of compressor and E-heater will be automatically shut-

off or turn on by TCO and ATCO.

If the water temperature is higher than 78°C, the ATCO will

automatically shut off the power of compressor and E-heater, and

reconnect it if the temperature falls down below 68°C.

the water temperature is higher than 85°C, the TCO will

automatically shut off the power of compressor and E-heater.

Storage tank

Water outlet

Temperature probe

(T5U)

Electric heater

Water inlet

Temperature probe

(T5L)

9 START-UP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun Solar Compak KHPA2 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info