Bedienungsanleitung KEF KIT100 (Seite 13 von 63) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

64278

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

specifications

KIT100 speakers KIT100PSW subwoofer

Design two-way closed box satellite speaker closed box powered subwoofer

Drive units 100mm (4 in.) Uni-Q array with 250mm (10 in.) long-throw

unit

14mm (0.6 in.) tweeter

NXT panel with 25mm (1 in.) exciter

magnetically shielded

Cabinets die-cast aluminium

Amplifiers 5xhigh power amplifier channels for the subwoofer and the main speak-

ers

Finish Stardust silver Stardust silver

Dimensions (H x WxD) 237 x 119 x 260 mm 398 x 176 x 515 mm

KIT100 DVD

Playback formats supported DVD, DVD-RW, DVD+RW, CD, CDR/RW, MP3 encoded CD

Tuner section AM/FM with RDS facility (Europe only)

Audio inputs cable/satellite, (analogue & optical digital) VCR and TV (analogue)

Audio output optical digital

Video inputs cable/satellite and VCR (S-video & composite)

Video outputs scart (Europe only), component, S-video and composite

Aerial inputs FM & AM (included)

Cabinet material die-cast zinc

Finish Stardust silver

Display mirror finish, blue VFD display with auto-dim function

Control infra-red remote control

Dimensions including feet 59 x 324 x 262 mm

(H x W x D) 2.32 x 12.75 x 10.31 in.

KEF AUDIO reserve the right, in line with continuous research and development, to amend or change specifications without prior notice.

E. & O.E.

glossary

Error messages

NO DISC Press OPEN/CLOSE and ensure that a disc has been correctly inserted into the DVD player

BAD DISC Check that the disc is inserted correctly with the label side upwards and that it is clean

INCORRECT REGION Check that the DVD region number matches that on the rear of the DVD player

No power

If there is no blue standby light, no response to pressing the ON/OFF button on the remote control or the POWER

button on the DVD player

• Make sure the system is switched on at the rear of the subwoofer speaker

• Check that the cable between the subwoofer and the DVD player is correctly connected at both ends and

screwed tight

• Check that the power cord is connected firmly at both ends

• Unplug the power cord from the outlet for 30 seconds to allow the system to reset

No sound

• Make sure “mute” is not lit on the display – if it is then press mute on remote control

• Increase the volume level

• Check speaker cable is connected to the rear of the subwoofer and screwed tight. Check that the speaker cable

is firmly pushed into both the left and right speakers

• Check that the external connections are firmly inserted and that the correct source is chosen e.g.

CBL/TV/VCR

Sound with no picture

• Check connections from the VCR and CBL source are correctly plugged into the rear of the DVD system

• Ensure the television is switched on and that the video input selection of your television is set to the correct

AV input. This can be done with the TV’s remote control, TV/VIDEO, INPUT or AUX IN buttons

• If you had a picture before but have just connected a different TV and there is now no picture, then the DVD

output settings of the DVD system may be incorrect for the new television – reset the DVD outputs to their

original out-of-the-box settings (see resetting factory defaults below)

• When using a Scart video connection to your TV you require a composite lead to view external sources

connected to the KEF Instant Theatre’s composite inputs. You require an S-video lead to view external inputs

connected to the KEF Instant Theatre’s S-video inputs

Remote control not working

• Check batteries and their polarity (+ and -)

• Make sure the DVD player’s front panel is not covered and that the remote control is pointing at the DVD

player

Radio does not work/or has poor reception

• Move the antennas further away from your television and other electrical equipment. The AM band is very

susceptible to interference from televisions

• Ensure the AM and FM antennas are connected

• Extend the antennas and adjust their position to improve radio reception

• Ensure AM antenna is upright

DVD or CD does not play

After pressing DVD/CD button and waiting a few seconds, LOAD should appear as the disc’s format information is

read by the DVD player

• Make sure the disc is properly inserted – label side up - eject the disc and re-insert it again

• Ensure disc is not dirty or scratched – clean the disc carefully

• Check that the disc region code matches the label on the back of the DVD system

Sound is distorted

• Check speaker connections

• Reduce level from other connected sources in case of interference

Subwoofer sound too high/low

• The level of bass from the subwoofer can be adjusted using the remote control

Speech missing on the Record or Multi room output

• Stereo mode must be selected to ensure that the centre channel is mixed onto the left and right Record/Multi

room outputs.

In the setting menu select Audio and change surround sound to “off” (stereo)

Resetting factory defaults

Your KEF Instant Theatre can be returned to its original out-of-the-box settings by pressing 3 buttons on the

DVD players front panel at

the same time:-

Press ‘PLAY/PAUSE’ and ‘<SKIP/PRESET’ (down) and ‘<VOLUME’ (down) simultaneously to reset with TV

standard set to NTSC for America

Press ‘PLAY/PAUSE’ and ‘<SKIP/PRESET’ (down) and ‘VOLUME>’ (up) simultaneously to reset with TV

standard set to PAL for Europe

The system must then be powered off before all the new settings will take effect

KIT100 Manual Multilingual Issue 2 10/1/11 11:43 Page 24

KEF KIT100 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info