Bedienungsanleitung Keiser M3i - Indoor Group Cycle (Seite 19 von 24) (Englisch)

738043

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

M3i INDOOR GROUP CYCLE 19

HOW TO EXERCISE ON THE BIKE

Start Your Exercise:

1. Set the Resistance Lever down and set the Pedal that

corresponds to your leading leg pointing forward.

2. Clip in, or step in, to the Pedal with your leading leg,

followed by your trailing leg to mount the bike.

3. Check that the cleats are properly secured to the Pedals,

or pull up on the Pedal Strap to tighten the Pedal Cage

(snug to t), before you start your exercise.

End Your Exercise:

1. Bring the Flywheel to a complete stop using the Pedals

or the Resistance Lever/Emergency Brake.

2. Kick your heel away from the bike to clip out. Pedal Cage

Riders: push down on the buckles to release the Pedal

Strap tension.

3. Step off of the higher Pedal rst, then the lower one, to

dismount.

The M3i cycle is intended for cardiovascular workout. Special programs have been designed for group exercise environments.

The bike must always be used in a supervised area under control of a trained and authorized instructor. The following

pages are a brief overview for the safe and proper operation of the bike.

POSTURE

RIDE SET UP

WARNING: To prevent injury, always wait until the

Flywheel comes to a complete stop before you attempt to

dismount the bike.

CAUTION: Ensure ride set up supports proper body positioning and all adjustments are secure before your ride. Be

sure to stretch and warm up prior to your ride to help avoid injury. Add time to cool down and stretch after your ride to

reduce stiffness/soreness. Failure to follow this instruction may result in injury.

Set the three points of contact on the bike to support proper body positioning:

SEAT Set the Seat height to align with the top of your hip when standing beside the bike.

HANDLEBAR Set the Handlebar height at, or slightly above, Seat height.

PEDALS Place the widest part of the foot on the Pedal, or clip in with cycling shoe cleats (SPD). Set the Resistance Lever

to a lighter gear and begin pedaling. Slow or stop pedaling and check your ride set up:

• Knee — A slight knee bend must be present when the foot is at the lowest position. The knee must not be locked (i.e., the

seat is too high) or have too much exion (i.e., the seat is too low).

• Handlebar Depth — Ensure setting supports a comfortable riding position: slight bend at the elbows, neutral spine

position, and shoulder blades drawn back and down.

• Seat Depth — The front of the knee should be in line with the widest part of the foot when the Pedal is positioned at three

o’clock (away from Flywheel).

Get off the bike before you make any adjustments.

As in any activity, proper posture is important. The preferred

riding posture is to:

• Maintain a neutral spine and slightly hinge forward

from the hips.

• Keep a natural curve in the low back.

• Activate the core (midsection; deep abdominal

muscles).

• Open up across the collarbones.

• Draw the shoulder blades back and down.

• Keep the elbows slightly bent when the hands are

placed on the handlebar.

• Maintain good lower body alignment from the hip to

the knee, down to the second toe. Figure 14. Proper Riding Posture

Neutral Spine

Core Activation

Hip Hinge

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Keiser M3i - Indoor Group Cycle Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info