Bedienungsanleitung Keiser M3i lite Indoor Group Cycle (Seite 16 von 24) (Englisch)

738045

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

M3i lite INDOOR GROUP CYCLE 16

BACKLIGHT SENSOR While the computer is awake, the backlight sensor automatically detects ambient light levels in the

room and turns on the backlight display when needed.

RPM (CADENCE) The RPM displays the revolutions per minute of the crank arm—also known in the cycling world as cadence—

and is roughly the speed at which the cyclist is pedaling.

POWER AND ENERGY The power output is displayed in Watts (currently generating) and Kilocalories (total value for the

workout). The computer toggles back and forth between Watts for eight seconds and Kilocalories for two seconds. The rated

accuracy for power between 30 and 160 RPM is ±5 Watts for power below 50 Watts, and ±10% for power above 50 Watts.

HEART RATE If there is no Heart Rate signal, a steady heart symbol and a zero will be displayed. If a user is wearing a Heart

Rate strap, once the computer locks onto the signal, the heart symbol will blink and display the heart rate.

Only POLAR® with coded GymLink heart rate sensors are compatible with Keiser M Series indoor cycles.

ELAPSED TIME The number shown reports the total workout time spent and will reset to zero after 60 seconds of inactivity

or if the computer is reset using the gear shifter.

GEAR Gears from 1 to 24 are displayed on the bottom left hand of the screen.

ODOMETER/TRIP DISTANCE When the computer is activated, the Odometer “ODO” will display the distance accrual of the

bike for the rst eight seconds. This feature is for service and maintenance purposes only. After approximately eight seconds

the Odometer “ODO” will disappear to display the Trip units for two seconds (“USA” = Miles, “EURO” = Kilometers), followed

by the Trip Distance for the remainder of the workout. Trip is a calculated distance value (at road run) based on power

production (Note: To change the Trip units, follow the instructions within the “Bluetooth® smart” procedure on page 18).

OVERVIEW

DISPLAY FEATURES

WORKOUT DATA

To view averages: RPM, Power, and Heart Rate, at any point in the workout, stop pedaling for three seconds. This will ash

your averages until you start pedaling again or until the computer goes to sleep after 60 seconds.

INTERVAL TRAINING

To initiate an interval, starting from a high gear drop the Resistance Lever to “GEAR 1” for 1/4 of a second and lift it up to a

higher gear immediately. “inL #” will display conrming the interval has started.

Repeat the above steps to end the interval (“inL End” will display) and the averages for that interval will blink.

Note: The averages displayed at the end of your workout when pedaling has stopped are inclusive of all pedaling times and

intervals that have taken place during your workout.

Bluetooth® smart ENABLED

The Bluetooth® smart enabled computer allows Bluetooth® smart Ready devices such as cellphones, tablets, and computers

to gather information about your workout. M3i lite compatible apps allow data to be stored to track progress over time and

make the data available to other tness applications. Classrooms are able to utilize real time performance tracking programs

which give the entire class an opportunity to see their performance compared with other participants in the class.

To receive and download workout information from your M3i lite, a Bike ID number is required, which identies your M3i lite

for individual or group Bluetooth discovery. The Bike ID number is viewable within the rst eight seconds (displayed as “bid”

and followed by any number 1 to 200, see Figure 13). To assign a Bike ID to your M3i lite, see “Bluetooth® smart” procedure on

page 18. Note: Bike ID set to “0” will not be discovered by Bluetooth devices.

COMPUTER DISPLAY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Keiser M3i lite Indoor Group Cycle Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info