Bedienungsanleitung Keithley 2001 (Seite 13 von 476) (Englisch)

598220

Zoom out

Zoom in

Vorherige Seite

1/476

Nächste Seite

General Information

2001-900-01 Rev. K/ August 2010 1-3

Model 2001 rear panel inputs (Keithley part number

CA-109).

Model 4288-1 Single Fixed Rack Mount Kit — Mounts a

single Model 2001 in a standard 19-inch rack.

Model 4288-2 Side-by-side Rack Mount Kit — Mounts

two instruments (Models 182, 428, 486, 487, 2001, 7001)

side-by-side in a standard 19-inch rack.

Model 4288-3 Side-by-side Rack Mount Kit — Mounts a

Model 2001 and a Model 199 side-by-side in a standard

19-inch rack.

Model 4288-4 Side-by-side Rack Mount Kit — Mounts a

Model 2001 and a 5-inch instrument (Models 195A, 196,

220, 224, 230, 263, 595, 614, 617, 705, 740, 775, etc.) side-

by-side in a standard 19-inch rack.

Models 7007-1 and 7007-2 Shielded IEEE-488 Cables —

Connect the Model 2001 to the IEEE-488 bus using shielded

cables and connectors to reduce electromagnetic interference

(EMI). The Model 7007-1 is one meter long; the Model

7007-2 is two meters long.

Models 8501-1 and 8501-2 Trigger Link Cables —

Connect the Model 2001 to other instruments with Trigger

Link connectors (e.g., Model 7001 Switch System). The

Model 8501-1 is one meter long; the Model 8501-2 is two

meters long.

Model 8502 Trigger Link Adapter — Allows you to

connect the Trigger Link of the Model 2001 to instruments

that use the standard BNC (In/Out) external triggering

technique.

Model 8530 IEEE-488 to Centronics Printer Adapter

Cable — Translates the IEEE-488 connector pinout and

signal level to a Centronics termination. This permits a

standard Centronics parallel printer to be connected to a

Model 2001 in TALK-ONLY mode.

Model 8605 High Performance Modular Test Leads —

Consists of two high voltage (1000V) test probes and leads.

The test leads are terminated with a banana plug with

retractable sheath on each end. (Each Model 2001 is shipped

with one set of these test leads.)

Model 8606 High Performance Probe Tip Kit — Consists

of two spade lugs, two alligator clips, and two spring hook

test probes. (The spade lugs and alligator clips are rated at

30V RMS, 42.4V peak; the test probes are rated at 1000V.)

These components are designed to be used with high

performance test leads terminated with banana plugs, such as

the Model 8605 High Performance Modular Test Leads.

The following test leads and probes are rated at 30V RMS,

42.4V peak:

Models 5805 and 5805-12 Kelvin Probes — Consists of

two spring-loaded Kelvin test probes with banana plug

termination. Designed to be used with instruments that

measure 4-terminal resistance. The Model 5805 is 0.9m

long; the Model 5805-12 is 3.6m long.

Model 5806 Kelvin Clip Lead Set — Includes two Kelvin

clip test leads (0.9m) with banana plug termination.

Designed for instruments that measure 4-terminal resistance.

A set of eight replacement rubber bands for the Model 5806

is available as Keithley P/N GA-22.

Model 8604 SMD Probe Set — Consists of two test leads

(3ft), each terminated with a surface mount device “grabber”

clip on one end and a banana plug with retractable sheath on

the other end.

Model 8610 Low Thermal Shorting Plug — Consists of

four banana plugs mounted to a 1-inch square circuit board,

interconnected to provide a short circuit among all plugs.

Model 8611 Low Thermal Patch Leads — Consists of two

test leads (3ft), each with a banana plug with a retractable

sheath at each end. These leads minimize the thermally-

induced offsets that can be created by test leads.

Model 8612 Low Thermal Spade Leads — Consists of two

test leads (3ft), each terminated with a spade lug on one end

and a banana plug with a retractable sheath on the other end.

These leads minimize the thermally-induced offsets that can

be created by test leads.

Model 8680 RTD Probe Adapter — This adapts RTDs with

terminated and unterminated cables to instruments with

banana jacks for measuring 4-terminal resistance. It has a

4-pin “T”-style connector and a 4-pin screw terminal block.

Model 8681 Miniature RTD Surface Probe — This is a low

cost platinum 4-wire-RTD with unterminated wires. It is

designed to measure the temperature of flat surfaces or free

space.

Model 8693 General Purpose/Immersion RTD Probe —

This probe has a platinum RTD sensor. It is designed for

immersion in liquids as well as other general purpose

applications.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Keithley 2001 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info