Bedienungsanleitung Kelvinator KWH62HRC (Seite 16 von 20) (Englisch)

478075

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Installations of the unit into the wall

AIR IN

AIR OUT

100mm minimum

OPTION A

AIR IN

LOUVRE

BRICK

WALL

45 BRICK CUT AWAY

TO CLEAR LOUVRES

FRONT

AIR OUT

AIR INAIR IN

TOP

VIEW

45 BRICK CUT AWAY

TO CLEAR LOUVRES

100mm

BRICK

WALL

100mm

OPTION B

Installation of the unit into the Housing

1. Remove the front panel as per the installation instruction

and slide the unit into the housing until it is firmly against

the rear of the housing. Care is required to ensure the foam

sealing strips on the inside of the housing remain in position.

2. Connect the air conditioner to the power and position

excess cord length beneath the air conditioner base.

3. Engage the chassis fixing brackets into the bottom housing

rail and secure to the base with the screw provided.

4. Re-install the front panel as per the installation instruction.

5. Switch the unit on. Check for operation of the unit and

check for vibration in the installation.

6. Fit the drain pan to the housing and run a drain line to a

suitable location if required.

Alternative method of installation if external

support cannot be provided.

FLASH OR SEAL AROUND EXTERNAL

WALL FRAME OR ARCHITRAVE

STURDY TIMBER

FRAME

TIMBER FRAMED

WALL OR PARTITION

SOLID TIMBER SUPPORT

STEADYING BRACKET

(ONE PER SIDE)

DRAIN PAN

ENSURE LOUVRES

ARE ENTIRELY

OUTSIDE THE WALL

Hole in the wall

Unit housing

Foam strip

Step 1

Remove the air conditioner from it's packaging, remove fixing

screws and slide the air conditioner out of it's housing (Refer

to Installation Steps).

Step 2

Prepare the hole in the wall so that the bottom of the housing

is well supported, the top has minimum clearance and the air

inlet louvres have clearance as shown in options A and B.

Holes from the outside through to the cavity should be sealed.

The housing should slope down towards the rear by about

10mm to allow water formed during operation to drain.

Step 3

Install the housing into the wall and secure. Ensure the

foam seals are not damaged. Flash, seal or fill gaps

around the inside and outside to provide satisfactory

appearance and protection against the weather, insects

and rodents.

Note: To assist in isolating transmission of normal operation

vibration into the wall, use the foam strip.

Fit the foam strip between the air conditioner housing and

the wall cavity.

Installation of the Housing

NOTE: UNIT MAY BE SUPPORTED BY A

SOLID FRAME FROM BELOW OR

BY A HANGER FROM A SOLID

OVERHEAD SUPPORT.

Preferred method of installation into a timber

framed wall, partition or window.

FLASH OR SEAL AROUND EXTERNAL

WALL FRAME OR ARCHITRAVE

STURDY TIMBER

FRAME ALL

AROUND UNIT

TIMBER FRAMED

WALL OR PARTITION

EXTERNAL SUPPORT

FRAME AT BALANCE

POINT OF A/C

ALTERNATIVELY, BRACKETS

AS ILLUSTRATED IN FOLLOWING

DIAGRAM MAY BE USED.

DRAIN PAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kelvinator KWH62HRC Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info