686377
8
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
8
A3 MIG Welder© Kemppi Oy 2018 1826
INTEGRATION GUIDE
At the wire feeder, make the connection to the
control cable connector.
At the power source, connect the cable to the
control cable connector at the rear of the power
source unit.
3.6.2 Welding cable
The welding cable delivers welding power from the power
source to the welding head.
At the wire feeder, connect the cable to the screw
terminal on the front of the unit.
At the power source, connect the cable to the (+)
connector at the rear of the power source unit.
3.6.3 Shielding gas hose
The shielding gas hose delivers the shielding gas to the
wire feeder. The wire feeder is equipped with a gas valve.
At the wire feeder, connect the hose to the shielding
gas snap connector.
Connect the other end of the hose to the shielding
gas supply.
3.7 Fieldbus communication
This welding system supports DeviceNet communication
Table 3.2: Kemppi Oy vendor ID and device description le
for the DeviceNet
Fieldbus Vendor ID Device description le
DeviceNet 1403 (integer) EDS
(Electronic Data Sheet)
The DeviceNet is wired into the 7-pin machine connector
located at the rear of the welding power source. It shares
the connector with a safety stop function (see Figure 3.8,
“Fieldbus connector pinout”).
Figure 3.8: Fieldbus connector pinout
Devicenet – Amphenol
1. D DeviceNet V- (GND)
2. C DeviceNet CAN_L
3. G DeviceNet Drain (Shield)
4. F DeviceNet CAN_H
5. E DeviceNet V+ (+24V)
Safety – Amphenol
1. A Safety stop signal
2. B Safety stop GND
The eldbus connector is clocked to avoid confusion
with other 7-pin connectors in the power source.
3.8 Safety stop
The safety stop is an input signal that halts the system
when the operator presses an emergency stop button.
The input is galvanically isolated from the other hardware
I/O of the welding power source. The signal shares the
same connector with the DeviceNet (see the Figure 3.8,
“Fieldbus connector pinout”).
The safety stop is congured by using the DIP switches.
F
G
Safety switch
Figure 3.9: Connecting safety stop switch
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi A3 MIG Welder wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info