Bedienungsanleitung Kemppi FastMig WFX 200-T (Seite 28 von 36) (Englisch)

686306

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

WFX 200, 300, 200 P Fe/Ss, 300 P Fe/Ss, 200-T, 300 P-T, 300-T, 200 AMC, 300 AMC

Err1

Power source is not calibrated or calibration data cannot be read

• Restart power source

• if the problem continues after multiple startups contact Kemppi service representative

Err 3

Overvoltage in the mains supply

• Check the mains voltage

Err 4

Power source is overheated

• Do not shut down, let the fans cool the machine.

• Check ventilation.

• If cooling fans are not running, contact Kemppi service representative.

Err 5

Mains power supply voltage is too low or one of the phases is missing or auxiliary supply is

faulty

• Check the mains supply and auxiliary supply and contact Kemppi service representative if

necessary.

Err 8

FPGA is not congured

• Restart the power source.

• If the error persists, contact Kemppi service representative

Err 9

Loose cable connections

• Check the voltage sensing cable, measurement cable and earth return cable.

Err 10

Illegal process

• The welding process is not available in this machine.

Err 12

Plus and minus DIX cable connectors are in contact

• Check welding cables

Err 27

Error in the liquid-cooling unit

• Check the connections in the cooling unit.

Err 42 or Err 43

Over current in wire feeder motor

• Check that the welding gun and consumable parts are properly mounted

Err 45

Gas guard alert

• Check the shielding gas, gas guard and all connections.

Err 50

The function is not activated in this machine

• If you need this function, order a licence for it from a Kemppi representative.

• WiseDemo period might be over.

Err 51

Rear feed roll may be loose

• Check that the feed rolls are properly tightened.

Err 52

Front feed roll may be loose

• Check that the feed rolls are properly tightened

Err 62

Power source is not connected or not identied by the wire feeder

• Check the intermediate cable and its connections.

Err 81

Welding program is not found

• If you need the welding program, order a licence for it from Kemppi representative.

MEM ERR & NO DAT

Machine cannot complete read or write functions on the wire feeder memory card

• Check the cables and connections.

• Contact Kemppi service representative.

NO BUS

Control panel cannot establish a connection to the CAN bus

• Check the at cables and the control panels.

• Contact Kemppi service representative.

SUB ERR

WF-number change error

• Connect only one wire feeder to system and try again.

NOTE! Many of these checks may be carried out by the operator. However certain checks relating to

mains power must be completed by an authorised trained electrician.

NOTE! In the case of an error code other than the listed above, contact Kemppi service

representative.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kemppi FastMig WFX 200-T Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kemppi FastMig WFX 200-T

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info