Bedienungsanleitung Kemppi Kemparc SYN 400 (Seite 12 von 26) (Englisch)

686382

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

You can change the gun selection by pressing buttons P3 and P4 again, as above. With a

liquid-cooled gun selected, the liquid cooling function is started when the power source is

started the next time.

2.2.6 Retrieving weld data

The weld data function allows you to return to the welding current and voltage used during

the previous session, with the weld data feature. To use the feature, press buttons P4 and P5

simultaneously.

2.2.7 Selecting the welding process

The welding process selector button P9 allows you to select the welding process you want to

use. You can select one of the following processes:

• normal MIG welding

• 1-MIG welding

• WiseThin (optional)

In normal MIG welding, the wire feed speed and welding voltage are adjusted separately.

Unlike the above, the 1-MIG and WiseThin processes are synergetic welding processes where

the welding voltage and other welding parameters are interconnected so that the welding

power and arc length are adjusted to attain optimal welding values.

The WiseThin process is an optional feature intended for welding automation. It must be

acquired separately and is therefore not available in all congurations.

2.2.8 Additional MIG features included in the standard delivery

The standard welding machine delivery includes three additional MIG features that facilitate

welding and improve weld quality. These additional features are creep start, hot start and

crater ll.

To use an additional MIG feature, press the feature selector button P10. Press the selector

button repeatedly to use one or several features. Only the additional features allowed for the

welding method you have chosen will be available.

Creep start

The purpose of the creep start feature is to make controlled weld start easier and smoothen

the initial stage of welding, for example when welding with high wire feed speeds. At the

beginning, the machine will use a slow wire feed speed until the wire touches the work piece

and the current starts owing.

Creep start is available for normal MIG welding and the synergetic 1-MIG welding.

Hot start

The purpose of hot start is to reduce start faults, for example when welding aluminium or

other materials with particularly good thermal conductivity. In this scenario, there is a xed

pre-gas time at the beginning of the welding, after which the welding power briey rises

above the specied power level. The power and time parameters for hot start can be specied

in the SETUP settings.

Hot start is available for synergetic 1-MIG welding.

Crater ll

The purpose of crater ll is to facilitate controlled nishing of welding and to reduce the

welding faults caused by the nal crater. When you press the welding gun trigger completely

down at the end of welding, the welding power is reduced to a preset crater ll level. To end

the crater ll stage, release the gun trigger. The crater ll parameters can be specied in the

SETUP settings.

Crater ll is available for synergetic 1-MIG welding.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kemppi Kemparc SYN 400 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info