Bedienungsanleitung Kemppi Minarc Evo 180 (Seite 11 von 18) (Englisch)

686272

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Site your equipment in a suitable location, ensuring there is adequate cable length to

complete the weld pass. Before you start welding, ensure you are comfortably positioned in

front of the work piece, and that you are well balanced with your weight equally distributed.

Ensure that the power source current setting is correct for the electrode size selected. Draw

the welding face shield over your eyes. (Electronic welding face shields like Kemppi BETA

90X, allow you to see the welding start point more accurately and better concentrate on the

welding process. This reduces the possibility of arc ash). Ensure others in the welding area are

aware that you're going to weld. To establish the arc, scratch the electrode on the surface of

the work piece.

As the arc starts to burn you will see a bright molten material form, this is molten slag,

formed from the electrode coating and the darker coloured material is the molten weld metal

itself, formed from the melting core wire. Hold the electrode at an angle of approximately

75–85 degrees from the horizontal, leaning away from the weld itself. Hold this position,

maintaining a 3 mm distance from electrode tip to work surface. As the electrode burns, this

arc length distance needs constant maintenance throughout the welding cycle. Slowly travel

the electrode away from the deposited weld pool material, maintaining a constant travel

speed. Your completed weld bead should be straight and of even width and bead height,

consistent in its appearance. Travel too slowly and the weld pool will get too big and may

burn through the weld piece, too fast and the resulting weld will be too small and may have

slag entrapments and/or poor strength. After welding, the solidied slag on the weld surface

should easily remove with a chipping hammer. Ensure you wear eye and face protection when

removing the slag from the weld surface.

3.3 TIG welding

Minarc Evo 180 can also be used for basic TIG welding and remote current control. The TIG

arc is started by the touch and lift ignition technique. Order numbers for the additional

equipment required for TIG welding and/or remote current control devices can be found in

Ordering codes section later in this manual. Ensure you select TIG process on the Minarc Evo

180 control panel before you commence welding.

The TIG process forms an arc between the tungsten electrode and the work piece. The arc

melts the work piece forming a molten weld pool. The arc and tungsten electrode mounted

in the TIG torch are shielded by an inert shielding gas that is connected to, and ows through,

the nozzle of the TIG torch. The gas required is argon and the ow rate is approximately 8 to 10

litres per minute. If necessary, suitable ller material is added to the weld pool to complete the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kemppi Minarc Evo 180 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kemppi Minarc Evo 180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info