Bedienungsanleitung Kenwood AT340 (Seite 9 von 70) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

463541

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

assembly and use

1 Remove the high speed outlet cover

ᕡ.

2 Fit the gearbox assembly onto the

mixer ᕢ.

3 Push the desired cutting plate onto

the shaft ᕣ. Each plate is numbered

for identification and the number

should be uppermost when the

plate is pushed onto the shaft.

4 Fit the sweeper onto the shaft ᕤ,

with the flat surface of the sweeper

against the plate.

●

For best results when using the

slicing/chipping plates, the sweeper

arm should be positioned opposite

the blade, as shown below.

5 Attach the lid assembly to the body,

line up the symbol on the lid

with on the body. Then turn to

symbol to lock into place ᕥ.

6 Fit the assembled attachment onto

the gearbox and turn to lock into

position ᕦ.

7 If required fit the extension chute

into the food outlet and push firmly

into place ᕧ. The extension chute

MUST be fitted when the

attachment is used with mixer

KM070 but can also be used with all

other mixers to direct the food into

the collecting bowl.

8 Connect the mixer to the power

supply and place a bowl under the

food outlet.

9 Choose which feed tube you want

to use. The pusher contains a

smaller feed tube for processing

individual items or thin ingredients.

To use the small feed tube -

first put the larger pusher inside the

feed tube ᕨ.

To use the larger feed tube -

use both pushers together ᕩ.

10 Put the food inside the feed tube.

11 Switch the mixer onto speed 3 and

at the same time push down evenly

with the pusher – never put your

fingers in the feed tube.

●

At the completion of the processing

operation, raising and lowering the

pusher several times may help to

reduce the amount of food left on

the cutting plate.

12 Switch off and unplug.

hints

●

Always use fresh ingredients

●

Don’t cut food up too small. Fill the

width of the large feed tube fairly

full. This prevents the food from

slipping sideways during processing.

Alternatively, use the small feed

tube.

●

When using a chipper plate, place

thin ingredients horizontally.

●

When slicing or shredding, food

placed upright comes out shorter

than food placed horizontally.

cleaning

●

Always switch off and unplug before

removing the attachment from the

kitchen machine.

●

Dismantle the attachment fully

before cleaning.

●

For easier cleaning always wash the

parts immediately after use.

●

Handle the cutting plates with care –

they are extremely sharp.

●

Never immerse the gearbox

assembly in water or allow it to get

wet.

All remaining parts can be washed

in hot soapy water, then dried

thoroughly. Take care as the cutting

plates are sharp. Alternatively wash

in the dishwasher (top rack only),

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood AT340 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info