Bedienungsanleitung Kenwood CMOS 200 (Seite 3 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

536417

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Install so that it does not obstruct the rear ﬁ eld of view.

• Install so that it does not protrude from the side of the car.

• Do not perform installation in rain or fog.

• When humidity is high, dry the surface to which the unit is to

be attached before installing.

• Moisture on the attachment surface reduces adhesive

strength, which may lead to the unit coming oﬀ .

• Do not attach the camera bracket to areas on the car body

treated with ﬂ uorocarbon resin, or glass.

• May result in the rear view camera falling oﬀ .

- Do not apply water to the unit.

- Do not expose the unit to rain.

- Do not subject the camera to unnecessary force.

- Thoroughly clean where tape is used for sticking on the

unit.

• Refer to the Instruction’s manual for details on connecting

the other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To

protect the wiring, wrap adhesive tape around them where

they lie against metal parts.

• Route and secure all wiring so it cannot touch any moving

parts, such as the gear shift, handbrake and seat rails.

• Do not route wiring in places that get hot, such as near the

heater outlet. If the insulation of the wiring melts or gets torn,

there is a danger of the wiring short-circuiting to the vehicle

body.

• When replacing the fuse, be sure to use only fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio antenna

cable and RCA cable as far away from each other as possible.

• Do not install the power supply box unit in places where it

may become subject to high temperatures or humidity, such

as:

- Places close to a heater, vent or air conditioner.

- Places exposed to direct sunlight, such as on top of the

dashboard or the rear shelf.

- Places that may be splashed by rain, for example close to

the door.

• Lay the cords by avoiding high-temperature areas. Use

corrugated tubes for wiring inside the engine room. If a cord

contacts a high-temperature area of the vehicle, the coating

may melt and cause short-circuiting, which may lead to a ﬁ re

or electric shock hazard.

Accessories

Camera (with camera bracket) ..........1

Camera connection cord ..........1

Power supply box..........1

Double-side adhesive tape (Large)..........1

Power cord ..........1

Switch unit..........1

Double-side adhesive tape (Small) ..........1

CMOS-300 only

The head unit connection cord is used for connection to

a Kenwood car navigation system equipped etc. with the

camera control function.

Waterproof packing ..........1

Camera bracket clamping screw..........1

Head unit connection cord ..........1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood CMOS 200 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info