Bedienungsanleitung Kenwood CMOS-220 (Seite 5 von 60) (Deutsch, Englisch, Holländisch, Französisch)

565392

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

CMOS-320/CMOS-220

ENGLISH

Installing the Camera/Adjusting its

angle

1 Decide the camera installation position.

2 Clean the camera installation surface.

Using a commercially available cleaner, wipe dirt, moisture

and oil away from the surface on which the camera bracket

is to be attached.

3 Loosen the camera bracket retaining screws.

Using a commercially available

Phillips screwdriver, loosen the

two retaining screws.

Perform steps 4 and 5 only when they are required.

4 If required, separate the camera bracket from

the camera and adjust the shape according to

the surface on which it will be attached.

Bend

Camera bracket

Adjust the camera bracket

shape so that it ﬁts the

camera installation

position.

5 Mount the camera on the camera bracket.

Mount so that the “KENWOOD” logo appears at the top.

6 Fix the camera temporarily with tape, etc.

Using a piece of tape, etc., ﬁx the camera temporarily.

12345

Install the camera at the center of the vehicle and not to

hide the number plate. And also install straight toward the

forward/reverse direction of the vehicle. Be careful not to

lean the camera toward other directions of the vehicle, etc.

7 Complete all of the required connections.

8 Display the camera video.

Before viewing the camera, apply the parking brake

and chock the wheels so that the vehicle will not move.

Otherwise, an unexpected accident may result.

For displaying the camera video, read the instruction manual

for your video monitor.

When the camera is installed as a rearview

camera:

Change the shift lever to the R (Reverse) range

to view the image of the rear of the vehicle.

When the camera is installed as a front camera

(CMOS-320 only):

Refer to the instruction manual of the unit that

you have connected this camera to, and display

the image of the front of the vehicle.

9 Adjust the camera angle.

When adjusting the camera angle, be careful not to stretch

the camera cord.

When installing CMOS-220 as a rearview

camera:

Adjust the angle so that the rear of the vehicle or the bumper

can be seen at the bottom of the monitor.

Vehicle rear part or bumper

When installing CMOS-320 as a rearview

camera:

Refer to “Display View Switching” (page 14) and switch the

image to [Overhead View]. Adjust the camera angle so that

the guideline and the parking lines become vertical.

Guideline

Installation

When installing CMOS-320 as a front camera:

Before adjusting the camera angle, perform “Camera ID

Setting” (page 13) and “Camera Setting Procedure” (page

10).

 When you select [Standard] for “Mounting Position Setting”,

switch the image to [Overhead View] (page 14) and adjust

the camera angle so that the guideline and the parking lines

become vertical.

 When you select [Lower] for “Mounting Position Setting”,

switch the image to [Corner View] (page 14) and then adjust

the angle of the camera to straighten the ground lines in the

left and right screens.

10 Set the camera.

When using CMOS-320 as a rearview camera:

Refer to page 9 to 13 and perform “Preparation Before

Camera Setting”, “Overhead View Image Adjustment” and

“Wide View Guideline Adjustment”.

When using CMOS-320 as a front camera:

When you select [Standard] for “Mounting Position Setting”,

refer to page 9 to 13 and perform “Preparation Before Camera

Setting”, “Overhead View Image Adjustment” and “Wide

View Guideline Adjustment”.

 When you select [Lower] for “Mounting Position Setting”,

refer to page 9 to 13 and perform “Preparation Before Camera

Setting” and “Overhead View Image Adjustment”. You cannot

perform “Wide View Guideline Adjustment”.

11 After adjusting the camera angle, tighten the

retaining screws ﬁrmly.

Inspect the retaining screws at times. If they are loose,

tighten them ﬁrmly.

Next page 3

LVT2720-001A.indb 5 14/02/14 15:10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood CMOS-220 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood CMOS-220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info