Bedienungsanleitung Kenwood CMOS-230 (Seite 3 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

606715

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

• Lay the cords by avoiding high-temperature areas. Use

corrugated tubes for wiring inside the engine room. If a

cord contacts a high-temperature area of the vehicle, the

coating may melt and cause short-circuiting, which may

lead to a  re or electric shock hazard.

Accessories

WARNING

• If you connect the ignition wire (Red) to the car chassis

(Ground), you may cause a short circuit, that in turn may

start a  re. Always connect those wires to the power source

running through the fuse box.

• Do not cut out the fuse from the ignition wire (Red). The

power supply must be connected to the wires via the fuse.

CAUTION

• If your car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and o with the ignition key. If you connect the ignition

wire to a power source with a constant voltage supply, as

with battery wires, the battery may die.

• If the fuse blows,  rst make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Install so that it does not obstruct the rear  eld of view.

• Install so that it does not protrude from the side of the car.

• Do not perform installation in rain or fog.

• When humidity is high, dry the surface to which the unit is

to be attached before installing.

• Moisture on the attachment surface reduces adhesive

strength, which may lead to the unit coming o .

• Do not attach the camera bracket to areas on the car body

treated with  uorocarbon resin, or glass.

• May result in the rear view camera falling o .

- Do not apply water to the unit.

- Do not expose the unit to rain.

- Do not subject the camera to unnecessary force.

- Thoroughly clean where tape is used for sticking on the

unit.

• Refer to the Instruction’s manual for details on connecting

the other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape.

To protect the wiring, wrap adhesive tape around them

where they lie against metal parts.

• Route and secure all wiring so it cannot touch any moving

parts, such as the gear shift, handbrake and seat rails.

• Do not route wiring in places that get hot, such as near the

heater outlet. If the insulation of the wiring melts or gets

torn, there is a danger of the wiring short-circuiting to the

vehicle body.

• When replacing the fuse, be sure to use only fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio

antenna cable and RCA cable as far away from each other

as possible.

Grommet..........1

Camera bracket clamping screw..........1

Camera [with camera bracket (A)] ..........1

Power cord ..........1

Camera bracket (B) ..........1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood CMOS-230 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info