Bedienungsanleitung Kenwood DDX5015BTR (Seite 66 von 76) (Englisch)

606274

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Error message list

If an error occurs while using the unit, a message

appears. Take appropriate action according to the

following message/remedy/cause list.

“No Signal”/“No Video Signal”:

• Start playback on the external component

connected to the AV-IN1 or iPod/AV-IN2 input

terminal.

• Start playback on the smartphone connected to

HDMI/MHL input terminal.

• Check the cords and connections.

• Signal input is too weak.

“Miswiring DC Offset Error”/“Warning DC Offset

Error”:

• A speaker cord has shorted or it has come into

contact with the car chassis. Wire or insulate the

speaker cord as appropriate, then reset the unit.

(Pages3 and 58)

“Parking off”:

• No playback picture is shown when the parking

brake is not engaged.

“Authorization Error”:

• Check whether the connected iPod/iPhone is

compatible with this unit. (Page65)

“USB Device Error”:

• The USB power voltage is abnormal.

• Turn off and turn on the unit.

• Connect another USB device.

“Panel Mecha Error”:

• The panel does not work properly. Reset the unit.

“No Navigation”:

• No navigation unit is connected.

“Connection Error”:

• The device is registered but the connection has

failed. Connect the registered device. (Page37)

“Please Wait...”:

• The unit is preparing to use the Bluetooth

function. If the message does not disappear, turn

off and turn on the unit, then connect the device

again (or reset the unit).

“No Voice Device”:

• The connected mobile phone does not have a

voice recognition system.

“No Data”:

• No phone book data is contained in the connected

Bluetooth phone.

“Initialize Error”:

• The unit has failed to initialize the Bluetooth

module. Try the operation again.

“Dial Error”:

• Dialing has failed. Try the operation again.

“Hung Up Error”:

• The call has not ended yet. Park your car, and use

the connected mobile phone to end the call.

“Pick Up Error”:

• The unit has failed to receive a call.

“Antenna Error”:

• The aerial has a short-circuit and the protective

circuit has activated.

• Check the Digital Radio aerial . If a passive aerial

without a booster is used, set aerial power to

“OFF”.

Troubleshooting

What appears to be trouble is not always serious.

Check the following points before calling a service

center.

• For operations with the external components,

refer also to the instructions supplied with the

adapters used for the connections (as well as

the instructions supplied with the external

components).

R General

No sound comes out of the speakers.

• Adjust the volume to the optimum level.

• Check the cords and connections.

No picture is displayed on the screen.

• Turn on the screen. (Page8)

The unit does not work at all.

• Reset the unit. (Page3)

The remote controller* does not work.

• Replace the battery.

* Purchase KNA-RCDV331 separately.

REFERENCESREFERENCES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DDX5015BTR Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DDX5015BTR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info