Bedienungsanleitung Kenwood DDX5056 (Seite 3 von 12) (Englisch)

465221

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

English

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring

work to professionals.

• Make sure to ground the unit to a negative 12V DC power

supply.

• Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too

much dust or the possibility of water splashing.

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

• If the power is not turned ON (“PROTECT” is displayed),

the speaker wire may have a short-circuit or touched the

chassis of the vehicle and the protection function may

have been activated. Therefore, the speaker wire should be

checked.

• Make sure that all wire connections are securely made by

inserting jacks until they lock completely.

• If your vehicle’s ignition does not have an ACC position, or

if the ignition wire is connected to a power source with

constant voltage such as a battery wire, the power will not

be linked with the ignition (i.e., it will not turn on and off

along with the ignition). If you want to link the unit’s power

with the ignition, connect the ignition wire to a power

source that can be turned on and off with the ignition key.

• Use a commercially available conversion connector if the

connector does not fit in the vehicle connector.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to

work if you share the - wires or ground them to any metal

part in the car.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

• Do not press hard on the panel surface when installing the

unit to the vehicle. Otherwise scars, damage, or failure may

result.

• This unit has the cooling fan to decrease the internal

temperature. Do not mount the unit in a place where the

cooling fan of the unit are blocked. Blocking these openings

will inhibit the cooling of the internal temperature and

result in malfunction.

Cooling fan

• Reception may drop if there are metal objects near the

Bluetooth antenna. (DNX5260BT only)

Bluetooth antenna unit

¤ CAUTION

Install this unit in the console of your vehicle.

Do not touch the metal part of this unit during and

shortly after the use of the unit. Metal part such as

the heat sink and enclosure become hot.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DDX5056 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DDX5056

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info