Bedienungsanleitung Kenwood DNX4150BTR (Seite 19 von 32) (Englisch)

606270

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English ñ 19

Call using call records

1) Touch [

] (incoming calls), [ ] (missed

calls), or [

] (outgoing calls).

2) Select the phone number from the list.

3) Touch [

Call using the phonebook

1) Touch [

2) Select the name from the list.

3) Select the number from the list.

4) Touch [

Call using the preset number

1) Touch [Preset #] to start calling the

corresponding phone number.

2) Touch [

Call by voice

You can make a voice call using the voice

recognition function of the cell-phone.

1) Touch [

2) Pronounce the name registered in the cell-

phone.

✎ NOTE

• For detailed operation, see Using Hands-Free Unit

(P.75) in the Instruction Manual.

Installation

Ñ Before Installation

Before installation of this unit, please note the

following precautions.

#WARNINGS

• If you connect the ignition wire (red) and the

battery wire (yellow) to the car chassis (ground), you

may cause a short circuit, that in turn may start a ﬁre.

Always connect those wires to the power source

running through the fuse box.

• Do not cut out the fuse from the ignition wire (red)

and the battery wire (yellow). The power supply

must be connected to the wires via the fuse.

#CAUTION

• Install this unit in the console of your vehicle.

Do not touch the metal part of this unit during and

shortly after the use of the unit. Metal part such as

the heat sink and enclosure become hot.

✎ NOTE

• Mounting and wiring this product requires skills and

experience. For best safety, leave the mounting and

wiring work to professionals.

•

ke sure to ground the unit to a negative 12V DC

power supply.

•

Do n

ot install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of water

splashing.

•

Do n

ot use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

•

If t

he power is not turned ON (“PROTECT” is displayed),

the speaker wire may have a short-circuit or touched

the chassis of the vehicle and the protection function

may have been activated. Therefore, the speaker wire

should be checked.

•

If y

our car’s ignition does not have an ACC position,

connect the ignition wires to a power source that

can be turned on and oﬀ with the ignition key. If you

connect the ignition wire to a power source with a

constant voltage supply, such as with battery wires,

the battery may be drained.

•

If t

he console has a lid, make sure to install the unit so

that the front panel will not hit the lid when closing

and opening.

•

If t

he fuse blows, ﬁrst make sure the wires aren’t

touching to cause a short circuit, then replace the old

fuse with one with the same rating.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DNX4150BTR Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DNX4150BTR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info