Bedienungsanleitung Kenwood DNX5160DABS (Seite 23 von 36) (Englisch)

672810

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

English |

InstallationInstallation

Before Installation

Before installation of this unit, please note the following

precautions.

#WARNINGS

• If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a ﬁre. Always connect those

wires to the power source running through the fuse box.

• Do not cut out the fuse from the ignition wire (red) and the

battery wire (yellow). The power supply must be connected

to the wires via the fuse.

#CAUTION

• Install this unit in the console of your vehicle.

Do not touch the metal part of this unit during and shortly

after the use of the unit. Metal part such as the heat sink

and enclosure become hot.

✎ NOTE

• Mounting and wiring this product requires skills and

experience. For best safety, leave the mounting and wiring

work to professionals.

•

ke sure to ground the unit to a negative 12V DC power

supply.

•

Do n

ot install the unit in a spot exposed to direct sunlight or

excessive heat or humidity. Also avoid places with too much

dust or the possibility of water splashing.

•

Do n

ot use your own screws. Use only the screws provided. If

you use the wrong screws, you could damage the unit.

•

If t

he power is not turned ON (“There is an error in the speaker

wiring. Please check the connections.” is displayed), the

speaker wire may have a short-circuit or touched the chassis

of the vehicle and the protection function may have been

activated. Therefore, the speaker wire should be checked.

•

If y

our car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and oﬀ with the ignition key. If you connect the ignition wire

to a power source with a constant voltage supply, such as with

battery wires, the battery may be drained.

•

If t

he console has a lid, make sure to install the unit so that the

front panel will not hit the lid when closing and opening.

•

If t

he fuse blows, ﬁrst make sure the wires aren’t touching to

cause a short circuit, then replace the old fuse with one with

the same rating.

•

sulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps on

the ends of the unconnected wires or the terminals.

•

nnect the speaker wires correctly to the terminals to which

they correspond. The unit may be damaged or fail to work if

you share the ¤ wires or ground them to any metal part in

the car.

•

en only two speakers are being connected to the system,

connect the connectors either to both the front output

terminals or to both the rear output terminals (do not mix front

and rear). For example, if you connect the ¢ connector of the

left speaker to a front output terminal, do not connect the ¤

connector to a rear output terminal.

•

ter the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

•

unt the unit so that the mounting angle is 30° or less.

•

is unit has the cooling fan to decrease the internal

temperature. Do not mount the unit in a place where the

cooling fan of the unit is blocked. Blocking these openings

will inhibit the cooling of the internal temperature and result

in malfunction.

Cooling fan

• Do not press hard on the panel surface when installing the unit

to the vehicle. Otherwise scars, damage, or failure may result.

• Reception may drop if there are metal objects near the

Bluetooth antenna.

Bluetooth antenna unit

DNX8160DABS DNX716WDABS DNX516DABS

DNX5160DABS/

DNX5160BTS/

DNX3160BT

Ñ Supplied accessories for installation

[1]

(1 m)

[2]

(3 m)

[3]

(3.5 m)

[4]

[1]

DNX8160DABS, DNX716WDABS, DNX5160DABS,

DNX516DABS, DNX5160BTS only

[2]

DNX3160BT only

[3]

DNX8160DABS, DNX5160DABS, DNX5160BTS, DNX3160BT

only

[4]

DNX8160DABS only

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DNX5160DABS Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DNX5160DABS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info