Bedienungsanleitung Kenwood DNX7170DABS (Seite 76 von 101) (Englisch)

672794

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

Connection/Installation

Before Installation

Before installation of this unit, please note the

following precautions.

# WARNINGS

• If you connect the ignition wire (red) and

the battery wire (yellow) to the car chassis

(ground), you may cause a short circuit, that

in turn may start a fire. Always connect those

wires to the power source running through

the fuse box.

• Do not cut out the fuse from the ignition wire

(red) and the battery wire (yellow). The power

supply must be connected to the wires via

the fuse.

# CAUTION

• Install this unit in the console of your vehicle.

Do not touch the metal part of this unit during

and shortly after the use of the unit. Metal part

such as the heat sink and enclosure become

hot.

NOTE

• Mounting and wiring this product requires

skills and experience. For best safety, leave the

mounting and wiring work to professionals.

• Make sure to ground the unit to a negative 12V

DC power supply.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not use your own screws. Use only the

screws provided. If you use the wrong screws,

you could damage the unit.

• If the power is not turned ON (“There is an

error in the speaker wiring. Please check the

connections.” is displayed), the speaker wire

may have a short-circuit or touched the chassis

of the vehicle and the protection function may

have been activated. Therefore, the speaker

wire should be checked.

• If your car’s ignition does not have an ACC

position, connect the ignition wires to a power

source that can be turned on and off with the

ignition key. If you connect the ignition wire to

a power source with a constant voltage supply,

such as with battery wires, the battery may be

drained.

• If the console has a lid, make sure to install the

unit so that the front panel will not hit the lid

when closing and opening.

• If the fuse blows, first make sure the wires

aren’t touching to cause a short circuit, then

replace the old fuse with one with the same

rating.

• Insulate unconnected wires with vinyl tape or

other similar material. To prevent a short circuit,

do not remove the caps on the ends of the

unconnected wires or the terminals.

• Connect the speaker wires correctly to the

terminals to which they correspond. The unit

may be damaged or fail to work if you share

the ¤ wires or ground them to any metal part

in the car.

• When only two speakers are being connected

to the system, connect the connectors either

to both the front output terminals or to both

the rear output terminals (do not mix front

and rear). For example, if you connect the ¢

connector of the left speaker to a front output

terminal, do not connect the ¤ connector to

a rear output terminal.

• After the unit is installed, check whether the

brake lamps, blinkers, wipers, etc. on the car

are working properly.

• Mount the unit so that the mounting angle is

30° or less.

• This unit has the cooling fan to decrease the

internal temperature. Do not mount the unit

in a place where the cooling fan of the unit is

blocked. Blocking these openings will inhibit

the cooling of the internal temperature and

result in malfunction.

Cooling fan

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DNX7170DABS Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DNX7170DABS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info