Bedienungsanleitung Kenwood DNX9180S (Seite 89 von 100) (Englisch)

672856

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Troubleshooting

89English

Troubleshooting

Problems and Solutions

If any trouble occurs, first check the following

table for possible problems.

NOTE

• Some functions of this unit may be disabled by

some settings made on this unit.

• What might seem to be a malfunction in your

unit may just be the result of slight misoperation

or miswiring.

Ñ About settings

• Cannot set up the subwoofer.

• Cannot set up subwoofer phase.

• No output from the subwoofer.

• Cannot set up the low pass filter.

• Cannot set up the high pass filter.

Subwoofer is not set to on.

 Set the subwoofer to on. See Speaker/ X’over

setup (P.68).

The dual zone function is enabled.

 Set the dual zone function to off. See Zone Control

(P.72).

• Cannot select the output destination of the

subsource in the dual zone.

• Cannot adjust the volume of the rear speakers.

The dual zone function is disabled.

 Set the dual zone function to on. See Zone Control

(P.72).

• Cannot set up the equalizer.

• Cannot set up the crossover network.

The dual zone function is enabled.

 Set the dual zone function to off. See Zone Control

(P.72).

Ñ About audio operations

Radio reception is poor.

The car antenna is not extended.

 Pull out the antenna all the way.

The antenna control wire is not connected.

 Connect the wire correctly. See Connecting the

system and external components (P.86).

Cannot select a folder.

The random play function is enabled.

 Turn off the random function.

Cannot perform repeat play during VCD playback.

The PBC function is enabled.

 Turn off the PBC function.

The specified disc does not play, but another one

plays instead.

The disc is quite dirty.

 Clean the disc. See Precautions on handling discs

(P.4).

The disc is severely scratched.

 Try another disc instead.

The sound skips when an audio file is being

played.

The disc is scratched or dirty.

 Clean the disc. See Precautions on handling discs

(P.4).

The recording condition is bad.

 Record the file again or use another disc.

Ñ Others

The Touch Sensor Tone doesn’t sound.

The preout jack is being used.

 The Touch Sensor Tone cannot be output from the

preout jack.

Error Messages

When you fail to operate the unit correctly, the

cause of the failure appears as the message on

the screen.

There is an error in the speaker wiring. Please

check the connections.

Protective circuit has been activated because a speaker

cord has shorted or it has come in contact with the car

chassis.

 Wire or insulate the speaker cord as appropriate and

turn the power off and on again.

Hot Error

When the internal temperature of this unit rises to 60°C

or more, the protection circuit is activated and you may

not be able to operate the unit.

 Use the unit again after reducing the temperature

of the unit.

Mecha Error

The disc player is malfunctioning.

 Eject the disc and try inserting it again. Contact the

KENWOOD dealer if this indicator continues blinking

or the disc cannot be ejected.

!B5A-2484-00_18DNX_M_En.indb 89 2018/02/19 20:36

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DNX9180S Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info