Bedienungsanleitung Kenwood DPF-1030 (Seite 22 von 24) (Englisch)

550571

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

÷Insert the power plug firmly to the AC outlet.

÷Turn the amplifier’s power ON.

÷Load the disc again with its label side up.

÷Insert the disc properly.

Wipe off the dust on the surface of the disc

referring to “Disc handling precautions”.

÷Replace the disc with a new one.

÷Leave the player for about 1 hour so that the

condensation is removed.

÷Press the 6 key.

÷Wipe off the dust on the disc surface referring

to “Disc handling precautions”.

÷Replace the disc with a new one.

÷Connect all connection cords firmly.

÷Adjust the output level with OUTPUT key on

the remote control unit.

÷Wipe off the dust on the disc surface referring

to “Disc handling precautions”.

÷Replace the disc with a new one.

÷Try selecting a place where no strong vibra-

tions occur by changing the installation place,

etc.

÷If automatic play is not required, remove the

disc from the player before setting the unit to

POWER OFF.

÷Power plug is loosely connected.

÷With the power plug connected to the switched

AC outlet of an amplifier, the power of the

amplifier is turned off.

÷Disc is loaded upside down.

÷Disc is loose.

÷Disc is dirty.

÷Disc is cracked.

÷Condensation has occurred on the optical lens

unit.

÷Play mode is not entered.

÷Disc is too dirty.

÷Disc is cracked.

÷The connection cords are inserted loosely.

÷Output level is attenuated too low.

÷Disc is too dirty.

÷Disc is cracked.

÷Oscillation is applied to this unit.

÷This unit is designed so that play begins auto-

matically when the unit is turned ON if a disc

is already loaded.

The unit is not turned on with the

POWER switch ON.

Disc is loaded, player does not play.

No sound.

Music is interrupted. (Sound is skipped.)

Play begins as soon as the unit is turned

ON.

Remote control operation is not possi-

ble.

÷Batteries are exhausted.

÷The remote control unit is too far away from

the main system, controlling angle is too large,

or there is an obstacle in between.

÷Replace with new batteries.

÷Operate the remote control unit within the

controllable range.

In case of difficulty

What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the

table below to see if the problem can be corrected before seeking help from your dealer or service representative.

Operation to reset

The microcomputer may fall into malfunction (impossibil-

ity to operate, erroneous display, etc.) when the connec-

tion cords are unplugged while unit is ON or due to an

external factor. In this case, execute the following method

to reset the microcomputer and return it to normal condi-

tion.

CD player unit

Remote control unit

÷Please be aware that resetting the CD player will erase all stored

information and return it to the factory settings.

Set the unit to POWER OFF by pressing the POWER

key, and after a few seconds, turn the unit POWER ON

by pressing the POWER key again.

Symptom Cause Remedy

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DPF-1030 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info