Bedienungsanleitung Kenwood DRV-830 (Seite 7 von 25) (Englisch)

683035

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

How to Install

Installation Procedure

Check that the vehicle is parked on a level

surface.

1. Attach the device to the mount

bracket. (accessory)

Insert the mount bracket into the bracket attach-

ment part of the device and attach it to the device.

Camera

lens side

Mount bracket

2. Determine where to mount the device.

Determine the mounting position in reference

to “Recommended installation position”.

3. Clean the mounting surface and then

ax the device to the windshield.

Use a commercially available cleaning cloth or

the like to wipe oﬀ all dirt and grease on the

mounting surface. Peel oﬀ the release paper of

the double-sided tape on the mount bracket

and push the bracket against the windscreen

to aﬃx it in place. Leave the device for 24 hours

before using it to enable the mounting

strength of the mount bracket to improve.

Release paper

4. Perform the cord wiring work.

Refer to “How to Wire” and perform the wiring

work.(➜ P. 14)

Adjust the device's mount angle, then

fasten it.

When adjusting the mount angle, check that the

camera's ﬁeld of vision is parallel to a ﬂat ground

surface and that the sky to ground ratio is equal.

There is a spirit level at [MENU] – [System

settings] – [Mouting support tools] – [Level].

(

➜

P. 34)

Use it to help adjustment of the mount angle.

Adjust the angle so that the moving circle

is as close as possible to the center of the

screen.

Windshield

Rear-view mirror

•

The “Adjust according to the vehicle”

adjustments must be made in order to use

the driving support functions. (➜ P. 17)

Do this in a ﬂat place with a line-of-sight

distance of approximately 200 meters.

Recommended installation position

z

Install the device in a position where it will not block the front view of the driver (position where hidden

by the rear-view mirror).

z

Install the device so that it is within the wiping range of the wiper.

z

Mounting the device to the center of the windshield behind the rear-view mirror will facilitate optimal

video recording.

Clip

Windshield

Doublesided

tape

Inside

vehicle

Outside

vehicle

Power cord

* Fix the power cord in place with commercially available soft

tape or the like.

Rearview

mirror

Power cord

Ceramic

part

Front pillar cover

Soft tape*

Front pillar

Power cord

CAUTION

When passing the power cord through the front pillar or another part, observe the points below when

performing the wiring work.

z

Wire the power cord farther forward or farther rearward than the airbag so that it does not interfere with

the airbag.

z

In the case of a vehicle in which the front pillar cover is ﬁxed in place with special clips or the like, the

clips may need to be replaced after you remove the front pillar cover. For how to remove the front pillar

cover, the availability of replacement parts and other information, contact the vehicle dealer.

z

Fix the power cord in place with commercially available soft tape or the like so that it does not interfere

with driving.

Recommended installation position

12 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DRV-830 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DRV-830

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info