Bedienungsanleitung Kenwood DRV-830 (Seite 12 von 25) (Englisch)

683035

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

Before Using

Manual recording

When the camera's [REC] button is pressed during

continuous

recording,

continuous

recording is

interrupted and manual recording starts. When manual recording ends, continuous recording resumes.

z

The recording time for manual recording is the 10 seconds before the [REC] button was pressed and a set

time after the button was pressed, selectable among 15 seconds (the setting upon purchase), 30 seconds

and 1 minute. (➜ P. 33)

z

If the [REC] button is pressed again before manual recording ends, manual recording is extended from

there for the set amount of time. The maximum recording time per ﬁle is 1 minute. When the recording

time reaches 1 minute, the ﬁle is split and recording starts on a new ﬁle.

Approx. 3 minutesApprox. 3 minutesApprox. 3 minutes

・・・・・

Approx. 3 minutes

・・・・・

Approx. 3 minutesApprox. 3 minutes

Overwrite Overwrite

Continuous recording

Press the [REC] button.

10 seconds before button

pressed recorded

Manual recording

15 seconds after button

pressed recorded

z

Upon purchase, overwriting is set to “OFF”. When the upper limit of the number of recordable

ﬁles is reached, manual recording is no longer possible.

Recorded le storage location

z

The ﬁles are stored in the “MANUAL” folder on the SD card. (➜ P. 45)

Still image recording

When the camera's [ ] button is pressed during continuous recording, a still image is recorded.

z

The resolution of the still images is the same resolution as set at “Resolution”. (➜ P. 33)

z

Recording is not interrupted when still images are recorded during recording.

Still image le storage location

z

The still image ﬁles are stored in the “PICTURE” folder on the SD card. (➜ P. 45)

Automatic still image capture

This function automatically captures a set number of still images at ﬁxed intervals.

When the

[ ]

button is pressed and held for over 1 second, the automatic still image capture

function turns on.

z

When the [ ] button is pressed and held for over 1 second or the set number of images are captured,

the automatic still image capture function turns oﬀ.

z

The number of images can be selected from among 10, 30 (the setting upon purchase) and 50. The capture interval

can be selected from among 1 minute, 5 minutes (the setting upon purchase), 15 minutes and 30 minutes. (➜ P. 33)

z

The resolution of the automatically captured still images is the same resolution as set at “Resolution”. (➜ P. 33)

z

If the camera's power is turned oﬀ while the automatic still image capture function is on, the automatic still

image capture function turns oﬀ. Capturing does not resume even if the camera's power is turned back on.

z

The capture function also turns oﬀ if the menu or shortcut menu screen is displayed or if the recording

mode is changed during recording.

Automatically captured still image le storage location

z

The still image ﬁles are stored in the “PICTURE” folder on the SD card. (➜ P. 45)

Parked recording when the power is off

•

To enable the parked recording function, the power must be connected with the CA-DR100

power cable for Dashcam (optional accessory).

z

Parked recording does not work if the power is turned oﬀ with the camera's power button

before turning the vehicle's engine key oﬀ.

z

Parked recording may not work if the power supply voltage is low due to deterioration of the

vehicle's battery, etc.

Parked recording

When the vehicle's engine key is turned oﬀ, the parked recording function is set to standby and the

camera monitors the vehicle for impacts. When an impact to the vehicle is detected, the power turns

on and parked recording starts. When parked recording ends, the power turns oﬀ and the function

is set back to standby.

z

The recording time for parked recording can be selected among OFF (parked recording not performed),

10 seconds (the setting upon purchase), 20 seconds and 30 seconds. When OFF (parked recording not

performed) is set, the parked recording function is turned oﬀ. (➜ P. 32)

z

With parked recording, recording starts several seconds after the impact is detected.

z

The sensitivity for detecting impacts can be set. (➜ P. 32)

Approx. 3 minutesApprox. 3 minutesApprox. 3 minutes

・・・・・

Approx. 3 minutes

・・・・・

Approx. 3 minutesApprox. 3 minutes

Overwrite Overwrite

Continuous recording

Standby

Impact detection

Parked recording for 10 seconds

z

No picture is displayed on the monitor screen during parked recording.

z

If parked recording has been performed, the user is notiﬁed when the power is turned on by

audio guidance and a monitor display.

z

The overwrite setting is set to “ON” upon purchase. When the upper limit of the number of

recordable ﬁles is reached, recording continues, overwriting the oldest ﬁles.

Disabling parked recording when getting in and out of the vehicle

Parked recording may be activated when the vibrations from the door closing are detected when

getting in and out of the vehicle. Parked recording can be disabled temporarily so that it is not per-

formed when the vibrations from the door closing are detected when getting in and out of the vehicle.

z

The start time (when getting out) and stop time (when getting in) can be selected among OFF (the setting

upon purchase), 30 seconds, 1 minute and 3 minutes. (➜ P. 32)

Parked recording le storage location

z

The parked recording ﬁles are stored in the “PARKING” folder on the SD card. (➜ P. 45)

22 23

Kenwood DRV-830 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DRV-830

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info