Bedienungsanleitung Kenwood DRV-N520 (Seite 4 von 48) (Englisch)

672783

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

FCC WARNING

This equipment may generate or use

radio frequency energy. Changes or

modifications to this equipment may

cause harmful interference unless the

modifications are expressly approved

in the instruction manual. The user

could lose the authority to operate this

equipment if an unauthorized change or

modification is made.

FCC NOTE

This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed

to provide reasonable protection against

harmful interference in a residential

installation.

This equipment may cause harmful

interference to radio communications, if

it is not installed and used in accordance

with the instructions. However, there

is no guarantee that interference will

not occur in a particular installation.

If this equipment does cause harmful

interference to radio or television

reception, which can be determined

by turning the equipment off and on,

the user is encouraged to try to correct

the interference by one or more of the

following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Precautions for Use

Precautions for Installation

• Install the device in a position where

it will not block the front view of the

driver (position where hidden by the

rear-view mirror).

• Install the device so that it is within the

wiping range of the wiper.

• Install the device in a position where it

will not interfere with the movement of

the rear-view mirror.

• Take care not to install the device over

the vehicle inspection sticker or other

sticker.

• Take care not to install the device where

it will interfere with driving or airbag

operation.

• When installing the device in a vehicle

equipped with a driving support system,

check the instruction manual of the

vehicle and then select an installation

location that will not interfere with the

driving support system.

• If the device is installed incorrectly,

event recording or parking recording

may not work correctly. Refer to "How to

Install" for the loosening of fixing knob,

installation orientation, installation angle,

and other information and then install

the device correctly.(P.8)

• Do not install the device near an

electrical component. Doing so may

cause flickering and noise.

• Use a commercially available cleaning

cloth or the like to wipe off all dirt and

grease on the mounting surface and

then fix the mount base in place. If the

device is re-affixed or mounted using,

for example, general-purpose double-

sided tape, the adhesion strength may

weaken and cause the device to fall.

• After mounting the device, leave it

for 24 hours before use to enable

the mounting strength of the mount

DRV-N520W_EN301.indd 4 2017/03/08 14:05

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DRV-N520 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DRV-N520

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info