Bedienungsanleitung Kenwood hm 537 mp (Seite 4 von 20) (Englisch)

159043

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Before applying power

Preparing the remote control

Insert batteries type R6/LR6 (“AA” size) into the

remote control.

Operation

When the standby indicator is lit, the power turns

ON when you press the POWER

button on the

remote control. When the power comes on, press

the button you want to operate.

Notes:

•The supplied batteries may have shorter lives than

ordinary batteries due to use during operation

checks.

•When the remote-controllable distance gets shorter

than before, replace both batteries with new ones.

• Placing the remote sensor in direct sunlight, or in

direct light from a high frequency fluorescent lamp

may cause a malfunction.

In such a case, change the location of the system

installation to prevent malfunction.

Connections

Connecting the FM antenna

Adjust the position of the FM antenna for the best

reception.

Connecting the AM antenna

Set up the AM loop antenna, and then connect it.

Speakers connection

• Connect the right speaker to terminal marked

“R” , with the red wire to + and the black wire

to –.

• Connect the left speaker to terminal marked

“L” , with the red wire to + and the black wire

to –.

• Clip the stripped portion of the speaker wire

as shown.

Notes:

•For optimal sound performance, it is recommended

to use the supplied speakers.

• Do not connect more than one speaker to any one

pair of +/– speaker terminal.

CAUTION

Be sure to adhere to the following, or proper

ventilation will be blocked causing damage

or fire hazard.

• Do not place any objects impairing heat ra-

diation onto the top of the unit.

•Leave some space around the unit (from the

largest outside dimension including projec-

tion) equal to or greater than, shown below.

Top panel : 50 cm

Back panel : 10 cm

1 2

CAUTION

• Place the unit where the AC power cord can

be easily unplugged.

•The power in this unit will not be completely

cut off from the AC wall outlet when the

power switch is turned OFF. To cut off the

power completely, unplug the AC power

cord from the AC wall outlet.

Channel space switching

(except for the Europe and Australia)

The space between radio channels has been

set to the one that prevails in the area to which

the system is shipped. However, if the current

channel space setting does not match the set-

ting in the area where the system is to be used,

for instance when you move from area 1 or

area 2 shown in the following table or vice

versa, proper reception of AM/FM broadcasts

cannot be expected. In this case, change the

channel space setting for each AM and FM

broadcast in accordance with your area by re-

ferring to the following table.

When the system is on, press TUNER band

button to select TUNER mode and waveband

of which you wish to set the channel space.

Then, while pressing 6 button, press 4

button to switch the channel space.

Area

CHANNEL

Space frequency

U.S.A., Canada and South

American countries

Other countries

FM: 100 kHz

AM: 10 kHz

FM: 50 kHz

AM: 9 kHz

*5469/01-07/EN 04.6.1, 11:19 AM4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood hm 537 mp Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood hm 537 mp

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info